| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Additive
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Agency Ratings
|
|
|||
|
RoHS Compliance
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|||
|
--
|
|
|
ASTM D792 |
|
--
|
|
g/cm³
|
ISO 1183 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus (0.0750 in, Compression Molded)
|
|
psi
|
ASTM D638, ISO 527-2 |
|
Tensile Strength (Yield, 0.0750 in, Compression Molded)
|
|
psi
|
ASTM D638, ISO 527-2 |
|
Tensile Elongation (Break, 0.0750 in, Compression Molded)
|
|
%
|
ASTM D638, ISO 527-2 |
|
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
|
|
mg
|
ASTM D1044 |
| Elastomers |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Set
|
|
%
|
ASTM D412 |
|
Tear Strength 2 (75°F)
|
|
lbf/in
|
ASTM D624 |
|
Compression Set
|
ASTM D395B, ISO 815 | ||
|
75°F, 22.0 hr
|
|
%
|
|
|
212°F, 22.0 hr
|
|
%
|
|
|
Clash-Berg Modulus (-31°F)
|
|
psi
|
ASTM D1043 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Durometer Hardness (Shore A, 0.0750 in, Compression Molded)
|
|
|
ASTM D2240 |
|
IRHD Hardness
|
|
|
ISO 48 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Brittleness Temperature
|
|
°F
|
ASTM D746, ISO 974 |
| Aging |
Nominal Value
|
Unit
|
Test Method
|
|
Change in Shore Hardness in Air (257°F, 168 hr)
|
|
|
ISO 188 |
|
Change in Ultimate Elongation (257°F, 168 hr)
|
|
%
|
ASTM D471 |
|
Change in Durometer Hardness (257°F, 168 hr)
|
|
|
ASTM D471 |
|
Change in Volume
|
ASTM D471 | ||
|
75°F, 168 hr, in Reference Fuel B
|
|
%
|
|
|
212°F, 168 hr, in ASTM Oil #1
|
|
%
|
|
|
212°F, 168 hr, in ASTM Oil #3
|
|
%
|
|
|
212°F, 168 hr, in Water
|
|
%
|
|
| Additional Information | |||
|
The value listed as Density-Specific Gravity, ASTM D792, was tested in accordance with ASTM D471.
Torsion Modulus, ASTM D1043, 75°F: 250psi Aging Tensile Strength, ASTM D573, 7 days, 257°F: 1210psi Torsion Modulus, ASTM D1043, -4°F: 1000psi Aging 100% Modulus, ASTM D573, 7 days, 257 °F: 400psi Aging Elongation At Break, ASTM D573 and ISO 188: 460% Fluid Resistance 7 Days in water, ISO 1817, at 212 °F: 10% Fluid Resistance 7 Days in ASTM Oil no. 1, ISO 1817, at 212 °F: -19% Fluid Resistance 7 Days in IRM 903 Oil no. 3, ISO 1817, at 212 °F: 12% Fluid Resistance 7 Days in ASTM Ref. Fuel no. B, ISO 1817, at 75 °F: 11% Rheological Viscosity, ASTM D3835, 1/300s at 374°F: 370Pa-s |
|||
| Related Terminology | |||
|
This supplier and product may also be known by these terms: APA, Advanced Polymer Alloys is a division of FerroProduct names can be difficult to match. You may have searched any one of these terms to find this product: Alcryn® 4660 BK, Alcryn 4660 BK, Alcryn® , Alcryn, Alcryn4660BK, 4660 BK, 4660BK, Melt Processable Rubber, MPR, Thermoplastic Elastomer, TPE, APA, MeltProcessableRubber, ThermoplasticElastomer, BK4660
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Weather Resistance, Weather Resistant, High Heat Resistance, Medium Flow, Medium Melt, Medium MFI, Good UV Resistance, UV Resistant, Ultraviolet Resistant, Ultraviolet Light Resistant.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Gaskets, Gasketing, Engineering Parts, Tubing, Tube.
|
|||
| Agency Ratings | |||
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Processing (Melt) Temp
|
|
°F
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 2Die C |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |