Home > Plastics > Materials > Sinkral® > Sinkral® E 332 - Datasheet

Sinkral® E 332 Data Sheet

Acrylonitrile Butadiene Styrene

Supplied by Versalis S.p.A.

View Complete Data Sheet Search 95000+ Data Sheets
Create Your Free Account!
Product Description
Sinkral E 332 is a medium heat injection moulding grade offering good flow and good impact resistance together with an excellent thermal stability during processing.

Designation: Thermoplastic ISO 2580-ABS 1,MGN,105-08-16-25

Thanks to a low Yellow Index and colour constancy, it is suitable for selfcolouring, mainly in the automotive industry (internal trim parts).

Grade available in natural colour only.
General  
Material Status 
  • Commercial: Active
Availability 
  • Africa & Middle East
  • Asia Pacific
  • Europe
  • Latin America
  • North America
Features 
  • Good Color Stability
  • Good Flow
  • Good Impact Resistance
  • Good Thermal Stability
  • Medium Heat Resistance
Uses 
  • Automotive Applications
  • Automotive Interior Trim
 
Appearance 
  • Natural Color
Forms 
  • Pellets
Processing Method 
  • Extrusion
  • Injection Molding
 
Multi-Point Data 
  • Specific Volume vs Temperature (ISO 11403-2)
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
ISO 1183
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
g/10 min
ISO 1133
Molding Shrinkage
%
Internal Method
Water Absorption (73°F, 24 hr)
%
ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2
psi
ASTM D638
Tensile Elongation 2 (Break)
%
ASTM D638
Flexural Modulus 3
psi
ASTM D790
Flexural Strength 3
psi
ASTM D790
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (73°F)
ft·lb/in²
DIN 53453
Charpy Unnotched Impact Strength
    DIN 53453
-40°F
 
 
73°F
 
 
Notched Izod Impact
     
-40°F, 0.126 in
ft·lb/in
ISO 180/4A
-4°F, 0.126 in
ft·lb/in
ISO 180/4A
32°F, 0.126 in
ft·lb/in
ISO 180/4A
73°F, 0.126 in
ft·lb/in
ISO 180/4A
-40°F 4
ft·lb/in²
ISO 180/1A
73°F 4
ft·lb/in²
ISO 180/1A
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
ISO 2039-2
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Annealed)
°F
ASTM D648
Vicat Softening Temperature
     
--
°F
ISO 306/A120
--
°F
ISO 306/B120
CLTE - Flow
in/in/°F
ASTM D696
Thermal Conductivity
Btu·in/hr/ft²/°F
ASTM C177
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
IEC 60093
Volume Resistivity
ohm·cm
IEC 60093
Electric Strength
V/mil
IEC 60243-1
Dielectric Constant (1 kHz)
 
IEC 60250
Dissipation Factor (1 kHz)
 
IEC 60250
Flammability
Nominal Value
Unit
Test Method
Flame Rating (0.0591 in)
 
UL 94
Glow Wire Ignition Temperature (0.118 in)
°F
IEC 60695-2-13
Additional Information
Nominal Value
Unit
Test Method
Designation
 
 
Features
Features may also be described by the following terms: Medium Heat Resistance, Good Flow, Good Impact Resistance, Good Thermal Stability, Good Color Stability.
Uses
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
Available Documents
Technical Datasheet (English)
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Extrusion
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Melt Temperature
°F
 
Notes
1Typical properties: these are not to be construed as specifications.
22.0 in/min
30.079 in/min
44 mm
 
UL and the UL logo are trademarks of UL LLC © 2014. All Rights Reserved.
The information presented on this datasheet was acquired by UL Prospector from the producer of the material. UL Prospector makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.