| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Filler / Reinforcement
|
|
|||
|
Uses
|
|
|||
|
Automotive Specifications
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|
|
ASTM D792 |
|
Molding Shrinkage - Flow (0.125 in)
|
|
in/in
|
ASTM D955 |
|
Water Absorption (73°F, 24 hr)
|
|
%
|
ASTM D570 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength (Yield, 73°F)
|
|
psi
|
ASTM D638 |
|
Tensile Elongation (Break, 73°F)
|
|
%
|
ASTM D638 |
|
Flexural Modulus (73°F)
|
|
psi
|
ASTM D790 |
|
Flexural Strength (73°F)
|
|
psi
|
ASTM D790 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact
|
|
ft·lb/in
|
ASTM D256 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Rockwell Hardness (R-Scale)
|
|
|
ASTM D785 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Deflection Temperature Under Load
|
ASTM D648 | ||
|
66 psi, Unannealed
|
|
°F
|
|
|
264 psi, Unannealed
|
|
°F
|
|
|
Melting Temperature
|
|
°F
|
|
|
CLTE - Flow
|
|
in/in/°F
|
ASTM D696 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Volume Resistivity
|
|
ohm·cm
|
ASTM D257 |
|
Dielectric Strength
|
|
V/mil
|
ASTM D149 |
|
Dielectric Constant (1 MHz)
|
|
|
ASTM D150 |
|
Dissipation Factor (1 MHz)
|
|
|
ASTM D150 |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating
|
|
|
UL 94 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: KOPLA PA66 KDG1030, KOPLA PA66 , KOPLAPA66KDG1030, KOPLAPA66, PA 66 KDG 1030, PA 66, PA66KDG1030, PA66, 66KDG, KDG 1030, KDG1030, Polyamide 66, Nylon 66, Polyamide, Nylon, KOPLA, Polyamide66, Nylon66, 1030KDG, 66PA
|
|||
| Generic Name | |||
|
Generic Name may also be described by the following terms: PA66.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (1).
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |