| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Uses
|
|
|||
|
Wire Types
|
|
|||
|
Agency Ratings
|
|
|||
|
RoHS Compliance
|
|
|||
|
UL File Number
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR) (200°C/5.0 kg)
|
|
g/10 min
|
ASTM D1238 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Deformation Under Load 3 (302°F)
|
|
%
|
ASTM D621 |
| Elastomers |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength (Break)
|
|
psi
|
ASTM D412 |
|
Tensile Elongation (Break)
|
|
%
|
ASTM D412 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Durometer Hardness (Shore A)
|
|
|
ASTM D2240 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Brittleness Temperature
|
|
°F
|
ASTM D746 |
| Aging |
Nominal Value
|
Unit
|
Test Method
|
|
Change in Tensile Strength in Air (277°F, 168 hr)
|
|
%
|
ASTM D573 |
|
Change in Ultimate Elongation in Air (277°F, 168 hr)
|
|
%
|
ASTM D573 |
|
Change in Tensile Strength (140°F, 168 hr, in IRM 902 Oil)
|
|
%
|
ASTM D471 |
|
Change in Ultimate Elongation (140°F, 168 hr, in IRM 902 Oil)
|
|
%
|
ASTM D471 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Dielectric Constant
|
ASTM D150 | ||
|
1 kHz
|
|
|
|
|
1 MHz
|
|
|
|
|
Dissipation Factor
|
ASTM D150 | ||
|
1 kHz
|
|
|
|
|
1 MHz
|
|
|
|
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating
|
|
|
UL 94 |
|
Oxygen Index
|
|
%
|
ASTM D2863 |
| Additional Information | |||
|
Maximum Continuous Operating Temperature, UL-1581: 105°C
|
|||
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Telcar® TL-8451, Telcar TL8451, Telcar® , Telcar, TelcarTL8451, TL, TL-8451, TL8451, TL:8451, TL/8451, TL+8451, TL_8451, TL 8451, Thermoplastic Elastomer, TPE, Teknor Apex, ThermoplasticElastomer, 8451TL
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Flexible Cord Jacketing, Industrial Cable Insulation, Terminal Cable Jacketing, Wire and Cable Applications, Wire & Cable Applications, Appliance Wire Insulation, Appliance Wire Jacketing.
|
|||
| Agency Ratings | |||
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): UL (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Rear Temperature
|
|
°F
|
|
|
Middle Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Nozzle Temperature
|
|
°F
|
|
|
Processing (Melt) Temp
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
|
Injection Pressure
|
|
psi
|
|
|
Injection Rate
|
|
|
|
|
Back Pressure
|
|
psi
|
|
|
Screw Speed
|
|
rpm
|
|
|
Cushion
|
|
in
|
|
| Injection Notes | |||
|
Drying is not necessary. However, if moisture is a problem, dry the pellets for 2 to 4 hours at 150°F (65°C)
|
|||
| Extrusion |
Nominal Value
|
Unit
|
|
|
Cylinder Zone 1 Temp.
|
|
°F
|
|
|
Cylinder Zone 2 Temp.
|
|
°F
|
|
|
Cylinder Zone 3 Temp.
|
|
°F
|
|
|
Cylinder Zone 5 Temp.
|
|
°F
|
|
|
Die Temperature
|
|
°F
|
|
| Extrusion Notes | |||
|
Screw Speed: 30 to 100 rpm
|
|||
| Notes |
| 1105°C |
| 2Typical properties: these are not to be construed as specifications. |
| 32000g weight |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |