| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Agency Ratings
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Coefficient of Friction 2 (vs. Itself - Dynamic)
|
|
|
ASTM D1894 |
| Films |
Nominal Value
|
Unit
|
Test Method
|
|
Secant Modulus
|
ASTM D882 | ||
|
1% Secant, MD: 1.2 mil
|
|
psi
|
|
|
1% Secant, TD: 1.2 mil
|
|
psi
|
|
|
Tensile Strength
|
ASTM D882 | ||
|
MD: Yield, 1.2 mil
|
|
psi
|
|
|
TD: Yield, 1.2 mil
|
|
psi
|
|
|
Tensile Elongation
|
ASTM D882 | ||
|
MD: Break, 1.2 mil
|
|
%
|
|
|
TD: Break, 1.2 mil
|
|
%
|
|
|
Seal Strength 2
|
|
lbf/in
|
Internal Method |
|
Seal Initiation Temperature (1.2 mil)
|
|
°F
|
Internal Method |
|
Oxygen Transmission Rate (Wet) (75°F, 1.2 mil, 0.0% RH)
|
|
cm³/100 in²/24 hr
|
ASTM F1927 |
|
Water Vapor Transmission 3
|
|
g/100 in²/24 hr
|
ASTM E96 |
|
Film Gauge
|
|
mil
|
Internal Method |
|
Yield (1.2 mil)
|
|
in²/lb
|
Internal Method |
| Optical |
Nominal Value
|
Unit
|
Test Method
|
|
Gloss (45°, 1.18 mil)
|
|
|
ASTM D2457 |
|
Haze 4 (1.18 mil)
|
|
%
|
ASTM D1003 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: NatureFlex™ 120 NE, NatureFlex 120 NE, NatureFlex™ , NatureFlex, NatureFlex120NE, 120 NE, 120NE, Cellulose, Regenerated, Cellulose Regenerated, Cellulose Acetate, CA, Innovia Films, CelluloseRegenerated, CelluloseAcetate, NE120
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Heat Seal, Flavor & Aroma Barrier, Flavor Barrier, Aroma Barrier, Flavor and Aroma Barrier, Gas Barrier, High Clarity, Deadfold Retention, Twist Retention, Deadfold and Twist Retention, High Gloss, Renewable Resources, From Renewable Resources, Renewable Resource Derived, Renewable Raw Materials, Renewable Resource Content.
|
|||
| Agency Ratings | |||
|
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EN (1), ASTM (1).
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 2Thickness: 1.18 mil |
| 3100°F, 90%RH, thickness: 1.18 mil |
| 42.5° wide angle |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |