EVERCAP™ 1190 enables the right performance properties to meet the demanding needs of lined closures. EVERCAP™ 1190 is designed for non-PVC liners of beverage closures where consistent seal, application torque, removal torque, and optimum sensory are required to maintain the quality of beverages. EVERCAP™ 1190 is designed for liners for applications such as roll on pilfer proof closures, pry off and twist off crown caps and other lined beverage closures. Complies with: - U.S. FDA 21 CFR 177.1520 (c) 2.2 - EU, No 10/2011 - JHOSPA, registered by Japan Hygienic Olefin and Styrene Plastics Association CN1, Compliance with China Food contact standards Consult the regulations for complete details.

EVERCAP™ DMDA-1220 NT 7 High Density Polyethylene Resin (HDPE) enables the right performance properties to meet demanding one-piece closure application needs. It is intended for use in compression molded one-piece closures designed for carbonated soft drinks, pressurized water and alternative beverages where sterilization processes such as hot fill and aseptic processes are used. EVERCAP™ DMDA-1220 delivers a combination of improved properties such as improved stiffness, improved ESCR, higher heat deflection temperature, and consistent processing. EVERCAP™ DMDA-1220 offers the ability to light-weight closures to meet the ongoing trend by industry for improved sustainability. Targeted Applications and Product Characteristics: - Compression Molded One-Piece Light Weight CSD, Pressurized Water and Alternative Beverage Closures - Excellent Stiffness, ESCR, and Impact Strength - Excellent Sensory Properties - Excellent Processing Characteristics - High Heat Deflection Temperature Complies with: - U.S. FDA 21 CFR 177.1520(c)3.2a - Europe Commission Regulation (EU) No 10/2011 - HPFB (Canada), No Objection Consult the regulations for complete details.

EVERCAP™ DMDA-1245 NT 7 High Density Polyethylene (HDPE) Resin is produced via UNIPOLTM Process Technology from Dow and is intended for use in a broad range of injection molding applications such as fitments, housewares, toys, food containers and pails. This resin has been designed to provide an excellent balance of oxygen barrier, toughness, environmental stress crack resistance and processability. Characteristics: - Injection molding - For injection molded fitments - Excellent balance of toughness, stress crack resistance and processability - Very narrow molecular weight distribution - For injection molded fitments Complies with: - U.S. FDA 21 CFR 177.1520 (c)3.2a - Canadian HPFB No Objection Consult the regulations for complete details.

EVERCAP™ DMDA-1247 NT 7 High Density Polyethylene (HDPE) Resin is a narrow molecular weight distribution high density homopolymer designed to offer excellent oxygen barrier, stiffness, low warpage, good/acceptable toughness, and good moldability. This resin is ideally suited for injection molded closures and other objects requiring oxygen barrier. Characteristics: - Excellent stiffness/modulus - Excellent warp resistance - Molded parts have high gloss, low odor - For injection molded closures and other parts needing high modulus Complies with: - U.S. FDA 21 CFR 177.1520 (c)2.2 - Canadian HPFB No Objection Consult the regulations for complete details.

EVERCAP™ DMDA-1260 NT 7 High Density Polyethylene Resin (HDPE) enables the right performance properties to meet demanding closure and fitment application needs. It is intended for use in compression and injection molded one piece beverage closures designed primarily for applications that undergo hot fill or aseptic sterilization processes. EVERCAP™ DMDA-1260 offers improved performance for injection molded fitments designed for fitted pouches where its balance of properties are desired. EVERCAP™ DMDA-1260 delivers a combination of improved properties such as improved stiffness, higher heat deflection temperature, improved ESCR, gaseous barrier, and easy processing versus alternative HDPE systems typically used for hot fill and aseptic sterilization processes. The end result is the ability to light weight closures that are s are longer term closure performance, easy opening closures without the use of slip agent and consistent processing. for aseptic applications where an acid wash can remove the slip agent and potentially plug wash water filters. Targeted Applications and Product Main Characteristics: - Compression and Injection Molded Light Weight Aseptic or Hot Fill Beverage Closures - Controlled Removal Torques without Slip for Aseptic Applications - Excellent Stiffness, ESCR, Gaseous Barrier and Impact Strength - Excellent Sensory Properties - Excellent Processing Characteristics - High Heat Deflection Temperature - Controlled Sensory Properties Complies with: - U.S. FDA 21 CFR 177.1520(c)3.2a - Europe Commission Regulation (EU) No 10/2011 - U.S. USP CLASS VI Consult the regulations for complete details.

EVERCAP™ DMDB-1220 NT 7 High Density Polyethylene Resin (HDPE) enables the right performance properties to meet demanding one-piece closure application needs. It is intended for use in compression molded one-piece closures designed for carbonated soft drinks, pressurized water and alternative beverages where sterilization processes such as hot fill and aseptic processes are used. EVERCAPTM DMDB-1220 delivers a combination of improved properties such as improved stiffness, improved ESCR, higher heat deflection temperature, and consistent processing. EVERCAPTM DMDB-1220 offers the ability to light-weight closures to meet the ongoing trend by industry for improved sustainability. Targeted Applications and Product Characteristics: - Compression Molded One-Piece Light Weight CSD, Pressurized Water and Alternative Beverage Closures - Excellent Stiffness, ESCR, and Impact Strength - Excellent Sensory Properties - Excellent Processing Characteristics - High Heat Deflection Temperature Complies with: - U.S. FDA 21 CFR 177.1520(c)3.2a - Europe Commission Regulation (EU) No 10/2011 - Canadian HPFB No Objection Consult the regulations for complete details.

EVERCAP™ DMDC-1260 NT 7 High Density Polyethylene Resin (HDPE) enables the right performance properties to meet demanding closure and fitment application needs. It is intended for use in compression and injection molded one piece beverage closures designed primarily for applications that undergo hot fill or aseptic sterilization processes. EVERCAP™ DMDC-1260 offers improved performance for injection molded fitments designed for fitted pouches where its balance of properties is desired. EVERCAP™ DMDC-1260 delivers a combination of improved properties such as improved stiffness, higher heat deflection temperature, improved ESCR, reduced ovalization during transport, and easy processing versus alternative HDPE systems typically used for hot fill and aseptic sterilization processes. EVERCAP™ DMDC-1260 offers the superior performance of EVERCAP™ DMDA-1260 with slip. Targeted Applications and Product Main Characteristics: • Compression and Injection Molded Light Weight Aseptic or Hot Fill Beverage Closures • Controlled Torque Values with Slip • Reduced closure ovalization during transport • Excellent Stiffness, ESCR, Gaseous Barrier and Impact Strength • Excellent Sensory Properties • Excellent Processing Characteristics • High Heat Deflection Temperature Complies with: • U.S. FDA 21 CFR 177.1520(c)3.2a • Europe Commission Regulation (EU) No 10/2011 • U.S. USP CLASS VI Consult the regulations for complete details.

EVERCAP™ DMDD-1210 NT 7 High Density Polyethylene Resin enables the right performance properties to meet demanding closure and fitment application needs. It is intended for use in both compression and injection molded closure applications. This resin has been designed to meet demanding performance requirements, especially in the areas of stiffness, impact strength, and sensory, while maintaining good processing characteristics beneficial to molders. Typical applications include injection molded closures for water, juice, dairy, and sports drinks, including hot fill and aseptic bottling applications, where minimizing the contribution of the package to the taste of the product and use of slip is a requirement. Main Characteristics: - Excellent Stiffness and Impact Strength - Excellent Organoleptic Properties - Excellent Processing Characteristics Complies with: - U.S. FDA 21 CFR 177.1520(c)3.1a. - EU, No 10/2011 Consult the regulations for complete details Additives: 1500 ppm Slip

EVERCAP™ DMDF-1250 NT 7 High Density Polyethylene Resin (HDPE) enables the right performance properties to meet demanding closure and fitment application needs. It is intended for use in both compression and injection molded closure applications including carbonated soft drink and hot fill closures. Its unique properties also make it suitable for living hinge closure applications. This resin has been designed to meet demanding performance requirements, especially in the areas of environmental stress crack resistance, impact strength, and sensory, while maintaining good processing characteristics beneficial to molders. Main Characteristics: - Excellent ESCR, Stiffness, and Impact Strength - Excellent Sensory Properties - Excellent Processing Characteristics - Contains Slip Agent Complies with: - U.S. FDA 21 CFR 177.1520(c)3.2a - Europe Commission Regulation (EU) No 10/2011 - Canadian HPFB No Objection Consult the regulations for complete details.

EVERCAP™ DMDA-1241 Experimental High Density Polyethylene (HDPE) Resin is produced via UNIPOL™ Process Technology from Dow and is intended for use as a polypropylene drop in replacement for a broad range of injection molding applications such as fitments, closures, and dispensing systems. This resin has been designed to provide an excellent balance of toughness, minimal shrinkage, balanced shrinkage, stiffness and processability. Main Characteristics: - Drop in Replacement for Polypropylene Injection Molded Closures and Dispensing Systems - Excellent Impact Strength - Excellent Processing Characteristics Complies with: - Complies with U.S. FDA 21 CFR 177.1520 (c)3.2a - EU, No 10/2011 - Consult the regulations for complete details