Bormed HE2581-PH is a resin intended for evaluation for use in Healthcare applications. Bormed HE2581-PH-03 is a bimodal high density polyethylene typically used for blow moulding of articles up to 10 litres. Material is characterised by easy processing and products with high stiffness and very good environmental stress crack resistance (ESCR). Material can also be used for containers produced with IBM technology. Material can be sterilised with ethylene oxide, steam and radiation up till 35 kGy; as a result of sterilisation by radiation some minor yellowing can occur. Applications Bormed HE2581-PH has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed HE2581-PH . - Bottles and containers for tablets - Bottles for IV-solutions - Bottles and containers for powder - Bottles for irrigation solutions - Bottles and containers for granules - Containers for fine chemicals or APIs This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special Features - Easy processing - High ESCR - Low extractables

Bormed HE7541-PH is a resin intended for evaluation for use in Healthcare applications. Bormed HE7541-PH-03 is a bimodal high-density polyethylene typically used in articles produced via injection moulding. This grade combines high environmental stress crack resistance and easy processing. Material can be sterilised with ethylene oxide, steam and radiation up to 35 kGy; as a result of sterilisation by radiation some minor yellowing can occur. Applications Bormed HE7541-PH has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed HE7541-PH . - Bottles and containers for tablets - Caps and closures - Bottles and containers for powder - Shoulders for tubes - Bottles and containers for granules This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special Features - Easy processing - High ESCR

Bormed HE9621PH3-01 is a resin intended for evaluation for use in Healthcare applications. HE9621PH3-01 is a high density polyethylene with narrow molecular weight distribution typically used in injection moulding of articles requiring medium flow with high rigidity. This grade is designed for articles which require high stiffness and low warpage. Material can be sterilised with ethylene oxide, steam and radiation up to 35 kGy; as a result of sterilisation by radiation some minor yellowing can occur. CAS-No.: 9002-88-4 Applications Bormed HE9621PH3-01 has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed HE9621PH3-01 . - Plungers for syringes - Packaging for powder, tablets & pills - Caps and closures This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special Features - High rigidity - Low extractables

Bormed LE6600-PH is a resin intended for evaluation for use in Healthcare applications. Bormed LE6600-PH is an additive free low density polyethylene which is used to produce soft and flexible packages for pharmaceutical products. The material can be converted via blow moulding, including BFS technology, or IBM into small bottles or ampoules. However, material can as well be used in injection moulding and blown film process. The flexibility of the materials will facilitate the dosing of the medicine when used in ampoules and bottles. Bormed LE6600-PH may be sterilized by steam, ethylene oxide or gamma radiation. CAS-No.9002-88-4

Bormed LE6607-PH is a resin intended for evaluation for use in Healthcare applications. Bormed LE6607-PH is an additive free low density polyethylene typically used in blow moulding articles. Material is characterised with a balanced in flexibility to facilitate to collapsibility of containers. Bottles and ampoules made from Bormed LE6607PH can be steam sterilised at maximum 110 °C. Products made from Bormed LE6607-PH can be sterilised by using ethylene oxide or radiation up to 35 kGy. Applications Bormed LE6607-PH has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed LE6607-PH . - Bottles for irrigation solutions - Ampoules for injectable solutions - Bottles for IV-solutions This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features - No additives

Bormed LE6609-PH is a resin intended for evaluation for use in Healthcare applications. Bormed LE6609-PH is an additive free low density polyethylene typically used in blow moulding articles . Material is characterised with a balanced inflexibility to facilitate to collapsibility of containers. Bottles and ampoules made from Bormed LE6609PH can be steam sterilised at temperatures above 110 °C. Products made from Bormed LE6609-PH can be sterilised by using ethylene oxide or radiation up to 35 kGy. Applications Bormed LE6609-PH has been evaluated according to different regulations and norms. Typical applications are mentioned below for Medical devices or Pharmaceutical & Diagnostic packaging. However, Borealis should be consulted for final approval to evaluate the use of Bormed LE6609-PH . - Bottles for irrigation solutions - Ampoules for injectable solutions - Bottles for IV-solutions This grade may only be used for the applications listed in the Product Datasheet and only to the extent that the application is within the scope of the tests set out in the Statement on Compliance to Regulations on Medical Use for that grade. If an application is not listed in the Product Datasheet, the grade can be used for such application only after express written consent of the Borealis Marketing Manager, Healthcare. Borealis prohibits the use of any healthcare grade product in an implantable device that is introduced into the human body by surgical intervention and that is intended to remain in place following surgical procedure. Special features - No additives