Body Double™ is a long lasting platinum-cure silicone rubber that can be applied directly to the skin to make molds of the face, hands and other body parts. The rubber cures quickly and will reproduce perfect detail from any original model – far better detail than any alginate! Body Double™ is skin safe and certified by an independent laboratory. One Casting or Many . . . For About The Same Price: unlike alginates, which are good for one only casting, Body Double™ will last for many castings of almost any material including plaster, Matrix™ Neo™, wax, resins (Smooth-Cast urethanes, polyester, etc.), lowtemperature melt metal alloys, etc. The amount of Body Double™ used per mold is less than most alginates, so the cost per mold is about the same. Adding HYPER-FOLIC™ release additive to Body Double™ silicone will create a self-releasing silicone which is easily removed from hair-covered body areas.. Body Double® "Standard Set" for larger surface areas. Working time of 5 minutes and a demold time of 30 minutes*. Body Double® "Fast Set" for fast turnaround. Working time of 90 seconds and a demold time of 7 minutes*. *Depending on material temperature, ambient temperature and body temperature - see "Preparation" below for details.

Body Double™ SILK is a self-releasing platinum-cure silicone rubber that can be applied directly to the skin to make molds of the face, hands and other body parts. The rubber cures quickly and will reproduce excellent detail from any original model. Cured material is skin safe and certified by an independent laboratory to ISO 10993-10, Biological evaluation of medical devices, Part 10: Tests for irritation and skin sensitization. Body Double™ SILK will release from closely cropped hair-covered skin surfaces (short beards, moustaches, eye-brows, pubic hair, etc.). Release cream or Hyperfolic are not needed when using Body Double™ SILK. Body Double™ SILK will last for many castings of almost any material including plaster, Matrix™ Neo™, wax, resins (Smooth-Cast urethanes, polyester, etc.) Body Double™ SILK has a working time of 6 minutes and a demold time of 20 minutes*. *Depending on material temperature, ambient temperature and body temperature - see "Preparation" below for details.

Body Double™ is a long lasting platinum-cure silicone rubber that can be applied directly to the skin to make molds of the face, hands and other body parts. The rubber cures quickly and will reproduce perfect detail from any original model – far better detail than any alginate! Body Double™ is skin safe and certified by an independent laboratory. One Casting or Many . . . For About The Same Price: unlike alginates, which are good for one only casting, Body Double™ will last for many castings of almost any material including plaster, Matrix™ Neo™, wax, resins (Smooth-Cast urethanes, polyester, etc.), lowtemperature melt metal alloys, etc. The amount of Body Double™ used per mold is less than most alginates, so the cost per mold is about the same. Adding HYPER-FOLIC™ release additive to Body Double™ silicone will create a self-releasing silicone which is easily removed from hair-covered body areas.. Body Double® "Standard Set" for larger surface areas. Working time of 5 minutes and a demold time of 30 minutes*. Body Double® "Fast Set" for fast turnaround. Working time of 90 seconds and a demold time of 7 minutes*. *Depending on material temperature, ambient temperature and body temperature - see "Preparation" below for details.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ silicones are high performance platinum cure liquid silicone compounds that are used for a variety of applications ranging from creating skin effects and other movie special effects to making production molds for casting a variety of materials. Because of the superior physical properties and flexibility of Dragon Skin™ rubbers, they are also used for medical prosthetics and cushioning applications. Dragon Skin™ rubbers are also used for a variety of industrial applications and have a service temperature range of a constant -65°F to +450°F (-53°C to +232°C). Great for Making Molds for a Variety of Applications - Available in Shore 10A, 15A, 20A and 30A, Dragon Skin™ silicones can be used to make exceptionally strong and tear resistant molds for casting plaster, wax, concrete (limited production run), resins and other materials. Dragon Skin™ 10 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Dragon Skin™ 10 silicones are Flame Rated to UL-94 HB specification and they meet the B1 classification for the GB 8624-2012 Fire Test to Building Material and Products (does not include ‘NV’ formulas). Time Tested, Versatile Special Effects Material – Soft, super-strong and stretchy, Dragon Skin™ 10 (Very Fast, Fast, Medium and Slow speeds) is used around the world to make spectacular skin and creature effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Cured rubber can also be painted with the Psycho Paint™ system. Cured material is skin safe and certified by an independent laboratory. Easy To Use – Dragon Skin™ silicones are mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with THI-VEX™. Rubber cures at room temperature (73°F/23°C) with negligible shrinkage. Vacuum degassing is recommended to minimize air bubbles in cured rubber.

Dragon Skin™ FX-Pro™ is a soft, stable, high performance platinum silicone rubber specifically designed for creating silicone makeup appliances and skin effects. Dragon Skin™ FX-Pro™ is compatible with Skin-Tite™ silicone adhesive as well as medical grade pressure sensitive adhesives for adhering silicone appliances temporarily to the skin. Cured material is skin safe and certified by an independent laboratory. Soft and stretchy FX-Pro™ has a Shore hardness of 2A. FX-Pro™ can be combined with SLACKER™ deadening agent to create a very soft silicone gel for filling encapsulated silicone pieces. An infinite number of color effects can be achieved by adding Silc-Pig™ silicone pigments. Cured rubber can also be painted with the Psycho Paint™ system. What Makes Dragon Skin™ FX-Pro™ Unique? - Soft - Shore 2A hardness allows for softer appliances using less SLACKER™ deadening agent - Low Viscosity - combined with long working time reduces bubbles and makes pouring easier - Cures Dry - will not leach silicone fluid - Long Working Time - 10-12 minute working time is good for larger pours or injections - Fast Cure - 40 minute cure time allows for quick turnaround of castings or molds - More Workable - Do More - has a ‘gel' stage - slushing the material into prosthetic molds is easier Dragon Skin™ FX Pro is mixed 1A:1B by weight or volume. Liquid rubber can be thinned with Silicone Thinner™ or thickened with Thi-Vex™ II. Rubber cures at room temperature (73°F / 23°C) with negligible shrinkage.

Ecoflex™ Near Clear™ rubbers are very soft, platinum silicones that are clearer than other Ecoflex™ silicones. Versatile and easy to use, Ecoflex™ Near Clear™ rubbers are mixed 1A:1B by weight or volume and cure at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing. Ecoflex™ Near Clear™ silicones are available in Shore 00-31 and Shore 00-45 hardness formulations. Cured material is skin safe and certified by an independent laboratory. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ Near Clear™ rubbers can be color pigmented with Silc Pig™ pigments, Cast Magic™ powders or Glow Worm™ powders for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity.

Ecoflex™ 00-35 FAST is a soft, fast cure platinum-catalyzed silicone that is versatile and easy to use. Parts A and B are mixed 1:1 by weight or volume, pot life is about 2.5 minutes and rubber cures in about 5 minutes at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and pouring. Rubber cures without a "tacky" surface, is very soft, very strong and very "stretchy", stretching many times its original size. Ecoflex™ 00-35 FAST is off-white translucent and can be color pigmented using Silc Pig® silicone color pigments. Certified Skin Safe - Material is skin safe and certified by an independent laboratory to OECD TG 439. Liquid Ecoflex™ 00-35 FAST will cure against the skin and can be used for life casting applications to make rubber molds that cure quickly and are good for casting wax, resins, etc. Ecoflex™ 00-35 FAST can also be used for a variety of skin safe applications including making fast skin safe appliances for special effects and cosplay, cushioning for orthopedic and orthotic devices worn on the body and much more. Ecoflex™ 00-35 FAST can also be used to make fast cure rubber molds with high elongation for casting a variety of materials.

Ecoflex™ Near Clear™ rubbers are very soft, platinum silicones that are clearer than other Ecoflex™ silicones. Versatile and easy to use, Ecoflex™ Near Clear™ rubbers are mixed 1A:1B by weight or volume and cure at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing. Ecoflex™ Near Clear™ silicones are available in Shore 00-31 and Shore 00-45 hardness formulations. Cured material is skin safe and certified by an independent laboratory. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ Near Clear™ rubbers can be color pigmented with Silc Pig™ pigments, Cast Magic™ powders or Glow Worm™ powders for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity.

Ecoflex™ GEL 2 is an extremely soft, platinum silicone rubber gel specifically designed for creating medical simulation devices, silicone makeup appliances, for cushioning, creating gaskets, encapsulation, outside-the-body shaping and enhancement products, silicone babies, theatrical prosthetics and more. and other applications requiring a very soft silicone material. Ecoflex™ GEL 2 has a Shore hardness of 000-34, this is below the Shore 00 hardness scale. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments. Certified Skin Safe - Cured material is skin safe and certified by an independent laboratory. Ecoflex™ GEL 2 is mixed 1A:1B by weight or volume. Rubber cures at room temperature (73°F / 23°C) with negligible shrinkage. Differences between cured Ecoflex™ Gel 2 and original Ecoflex™ Gel include; Gel 2 is “dryer” and slightly less sticky. While the Shore hardness is about the same, the Gel 2 has a higher modulus that makes this gel feel firmer. Like the original, Gel 2 cannot be handled as a “stand alone” product. It should be encapsulated in another silicone like Dragon Skin, Q-Ballz encapsulant or other suitable membrane.

Ecoflex™ GEL is an extremely soft, platinum silicone rubber gel specifically designed for creating silicone makeup appliances, for cushioning, creating gaskets, encapsulation, and other applications requiring a very soft silicone material. Ecoflex™ GEL has a Shore hardness of 000-35, this is below the Shore 00 hardness scale. Because Ecoflex™ GEL is so soft, it works very well as a silicone gel for filling encapsulated silicone makeup appliances and prosthetics. An infinite number of color effects can be achieved by adding Silc Pig® silicone pigments. As Ecoflex™ GEL is very tacky when cured, in some situations, it is recommended that Ecoflex™ GEL be encapsulated with another non-tacky platinum silicone such as Dragon Skin FX Pro, or another suitable membrane. Ecoflex™ GEL is mixed 1A:1B by weight or volume. Rubber cures at room temperature (73°F / 23°C) with negligible shrinkage.

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing, or you can choose to mix and dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ rubbers are water white translucent and can be color pigmented with Silc Pig™ pigments for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity. THI-VEX™ silicone thickener can be added by weight to Ecoflex™ silicones for brushable applications. Soft, Softer, Softest . . . Ecoflex™ rubbers are based on Smooth-On’s Dragon Skin™ technology and are currently available in many different hardnesses: Shore A-5, Shore 00-10, 00-20, 00-30 and 00-50. They are suitable for a variety of applications including making prosthetic appliances, cushioning for orthotics and special effects applications (especially in animatronics where repetitive motion is required). Ecoflex™ 5 has a pot life of 1 minute and a demold time of 5 minutes – Available only in dispensing cartridges. Ecoflex™ 00-33 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Ecoflex™ 00-20 FAST has a 20 minute pot life and 1 hour cure time. Cured Ecoflex™ is skin safe and certified by an independent laboratory. Note: Ecoflex™ 00-10 cures with a “tacky” surface.

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing, or you can choose to mix and dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ rubbers are water white translucent and can be color pigmented with Silc Pig™ pigments for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity. THI-VEX™ silicone thickener can be added by weight to Ecoflex™ silicones for brushable applications. Soft, Softer, Softest . . . Ecoflex™ rubbers are based on Smooth-On’s Dragon Skin™ technology and are currently available in many different hardnesses: Shore A-5, Shore 00-10, 00-20, 00-30 and 00-50. They are suitable for a variety of applications including making prosthetic appliances, cushioning for orthotics and special effects applications (especially in animatronics where repetitive motion is required). Ecoflex™ 5 has a pot life of 1 minute and a demold time of 5 minutes – Available only in dispensing cartridges. Ecoflex™ 00-33 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Ecoflex™ 00-20 FAST has a 20 minute pot life and 1 hour cure time. Cured Ecoflex™ is skin safe and certified by an independent laboratory. Note: Ecoflex™ 00-10 cures with a “tacky” surface.

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing, or you can choose to mix and dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ rubbers are water white translucent and can be color pigmented with Silc Pig™ pigments for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity. THI-VEX™ silicone thickener can be added by weight to Ecoflex™ silicones for brushable applications. Soft, Softer, Softest . . . Ecoflex™ rubbers are based on Smooth-On’s Dragon Skin™ technology and are currently available in many different hardnesses: Shore A-5, Shore 00-10, 00-20, 00-30 and 00-50. They are suitable for a variety of applications including making prosthetic appliances, cushioning for orthotics and special effects applications (especially in animatronics where repetitive motion is required). Ecoflex™ 5 has a pot life of 1 minute and a demold time of 5 minutes – Available only in dispensing cartridges. Ecoflex™ 00-33 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Ecoflex™ 00-20 FAST has a 20 minute pot life and 1 hour cure time. Cured Ecoflex™ is skin safe and certified by an independent laboratory. Note: Ecoflex™ 00-10 cures with a “tacky” surface.

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing, or you can choose to mix and dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ rubbers are water white translucent and can be color pigmented with Silc Pig™ pigments for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity. THI-VEX™ silicone thickener can be added by weight to Ecoflex™ silicones for brushable applications. Soft, Softer, Softest . . . Ecoflex™ rubbers are based on Smooth-On’s Dragon Skin™ technology and are currently available in many different hardnesses: Shore A-5, Shore 00-10, 00-20, 00-30 and 00-50. They are suitable for a variety of applications including making prosthetic appliances, cushioning for orthotics and special effects applications (especially in animatronics where repetitive motion is required). Ecoflex™ 5 has a pot life of 1 minute and a demold time of 5 minutes – Available only in dispensing cartridges. Ecoflex™ 00-33 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Ecoflex™ 00-20 FAST has a 20 minute pot life and 1 hour cure time. Cured Ecoflex™ is skin safe and certified by an independent laboratory. Note: Ecoflex™ 00-10 cures with a “tacky” surface.

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing, or you can choose to mix and dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ rubbers are water white translucent and can be color pigmented with Silc Pig™ pigments for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity. THI-VEX™ silicone thickener can be added by weight to Ecoflex™ silicones for brushable applications. Soft, Softer, Softest . . . Ecoflex™ rubbers are based on Smooth-On’s Dragon Skin™ technology and are currently available in many different hardnesses: Shore A-5, Shore 00-10, 00-20, 00-30 and 00-50. They are suitable for a variety of applications including making prosthetic appliances, cushioning for orthotics and special effects applications (especially in animatronics where repetitive motion is required). Ecoflex™ 5 has a pot life of 1 minute and a demold time of 5 minutes – Available only in dispensing cartridges. Ecoflex™ 00-33 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Ecoflex™ 00-20 FAST has a 20 minute pot life and 1 hour cure time. Cured Ecoflex™ is skin safe and certified by an independent laboratory. Note: Ecoflex™ 00-10 cures with a “tacky” surface.

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing, or you can choose to mix and dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ rubbers are water white translucent and can be color pigmented with Silc Pig™ pigments for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity. THI-VEX™ silicone thickener can be added by weight to Ecoflex™ silicones for brushable applications. Soft, Softer, Softest . . . Ecoflex™ rubbers are based on Smooth-On’s Dragon Skin™ technology and are currently available in many different hardnesses: Shore A-5, Shore 00-10, 00-20, 00-30 and 00-50. They are suitable for a variety of applications including making prosthetic appliances, cushioning for orthotics and special effects applications (especially in animatronics where repetitive motion is required). Ecoflex™ 5 has a pot life of 1 minute and a demold time of 5 minutes – Available only in dispensing cartridges. Ecoflex™ 00-33 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Ecoflex™ 00-20 FAST has a 20 minute pot life and 1 hour cure time. Cured Ecoflex™ is skin safe and certified by an independent laboratory. Note: Ecoflex™ 00-10 cures with a “tacky” surface.

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage. Low viscosity ensures easy mixing and de-airing, or you can choose to mix and dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion. Ecoflex™ rubbers are water white translucent and can be color pigmented with Silc Pig™ pigments for creating a variety of color effects. You can also add Smooth-On’s Silicone Thinner™ to further lower the viscosity. THI-VEX™ silicone thickener can be added by weight to Ecoflex™ silicones for brushable applications. Soft, Softer, Softest . . . Ecoflex™ rubbers are based on Smooth-On’s Dragon Skin™ technology and are currently available in many different hardnesses: Shore A-5, Shore 00-10, 00-20, 00-30 and 00-50. They are suitable for a variety of applications including making prosthetic appliances, cushioning for orthotics and special effects applications (especially in animatronics where repetitive motion is required). Ecoflex™ 5 has a pot life of 1 minute and a demold time of 5 minutes – Available only in dispensing cartridges. Ecoflex™ 00-33 AF is an anti-fungal silicone suitable for making a variety of skin-safe cushioning device configurations that resist fungi for orthopedic and orthotic applications. Ecoflex™ 00-20 FAST has a 20 minute pot life and 1 hour cure time. Cured Ecoflex™ is skin safe and certified by an independent laboratory. Note: Ecoflex™ 00-10 cures with a “tacky” surface.

Equinox™ Silicone Putty Products are new silicone compounds (platinum catalyst) that can be easily mixed and applied by hand to a variety of surfaces. Equinox™ Putty is mixed in equal amounts (1A:1B) by volume. Equinox™ 35 has a pot life of about 1 minute with a cure time of about 7 minutes at room temperature (73°F/23°C). Equinox™ 38 has a pot life of 4 minutes with a cure time of 30 minutes and Equinox™ 40 is a slower version with a 30 minute pot life and 5 hour demold time. Shrinkage is low and cured rubber is exceptionally strong (very high tensile strength), durable and will resist high temperatures (for casting low-temperature melt metal alloys). They also resist cure inhibition. Equinox™ Silicones are also FOOD SAFE and can be used for culinary applications. (See separate technical bulletin for usage instructions available at www.smooth-on.com).

Equinox™ Silicone Putty Products are new silicone compounds (platinum catalyst) that can be easily mixed and applied by hand to a variety of surfaces. Equinox™ Putty is mixed in equal amounts (1A:1B) by volume. Equinox™ 35 has a pot life of about 1 minute with a cure time of about 7 minutes at room temperature (73°F/23°C). Equinox™ 38 has a pot life of 4 minutes with a cure time of 30 minutes and Equinox™ 40 is a slower version with a 30 minute pot life and 5 hour demold time. Shrinkage is low and cured rubber is exceptionally strong (very high tensile strength), durable and will resist high temperatures (for casting low-temperature melt metal alloys). They also resist cure inhibition. Equinox™ Silicones are also FOOD SAFE and can be used for culinary applications. (See separate technical bulletin for usage instructions available at www.smooth-on.com).

Equinox™ Silicone Putty Products are new silicone compounds (platinum catalyst) that can be easily mixed and applied by hand to a variety of surfaces. Equinox™ Putty is mixed in equal amounts (1A:1B) by volume. Equinox™ 35 has a pot life of about 1 minute with a cure time of about 7 minutes at room temperature (73°F/23°C). Equinox™ 38 has a pot life of 4 minutes with a cure time of 30 minutes and Equinox™ 40 is a slower version with a 30 minute pot life and 5 hour demold time. Shrinkage is low and cured rubber is exceptionally strong (very high tensile strength), durable and will resist high temperatures (for casting low-temperature melt metal alloys). They also resist cure inhibition. Equinox™ Silicones are also FOOD SAFE and can be used for culinary applications. (See separate technical bulletin for usage instructions available at www.smooth-on.com).

EZ-Brush® Vac Bag Silicone is a brushable platinum cure silicone developed especially for making high performance, re-usable vacuum bags. EZ-Brush® Vac Bag Silicone is easy to mix and apply. Mix ratio is 1A:1B by volume and rubber can be applied with a brush or spatula to vertical surfaces without sagging. Pot life is 30 minutes, recoat time is 1 hour. Rubber cures with negligible shrinkage to a soft, flexible rubber (Shore 20A) with very high elongation and tear strength. Newly made bags can be removed from the tool in 3.5 hours and used immediately in production with polyester or epoxy resin systems and will withstand temperatures up to 500° F /260° C. Compared to conventional vacuum bagging systems, EZ-Brush® Vac Bag Silicone is much faster at delivering a production-ready silicone bag resulting in a tremendous time and labor savings. Since bags are re-usable, long term material costs are greatly reduced.

EZ~Spray® 35 is a platinum cure silicone rubber developed specifically for spraying through the EZ~Spray® Junior Cartridge System. With no or minimal surface preparation, EZ~Spray® 35 can be sprayed onto vertical surfaces for making fast rubber molds of large surface areas. After a suitable thickness is attained, EZ~Spray® 35 cures in 1 hour with negligible shrinkage to a durable mold rubber good for production casting resins, foams, concrete, plaster and other materials. Application of a support shell is achieved by spraying Smooth-On's EZ~Spray® Plastic over the rubber mold after it has fully cured. Read the EZ~Spray® Junior manual prior to spraying.

EZ~Spray® Foam is a polyurethane foam compound that can be conveniently sprayed using Smooth-On's EZ~Spray® Junior System. Foam cures quickly to strong, lightweight and impact resistant 8 lb. rigid foam that can be used for a variety of applications including making lightweight castings. Foam can also be sprayed over certain rubber mold configurations as a mother mold material. For more information, refer to Smooth-On's EZ~Spray® Junior manual and video.

EZ~Spray® Silicone 20 and 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 20 cures in about 20 minutes while EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials. EZ~Spray® Silicone 20 and 22 silicones are effective at making fast, cost effective vacuum bags for producing composite parts. Newly sprayed or injected bags can be removed from the mold in a matter of minutes and used immediately in production with polyester or epoxy resin systems. The advantage that EZ~Spray® Silicone offers vs. conventional vacuum bagging systems is the speed at which a production-ready silicone bags can be made resulting in significant time and labor savings. Read the EZ~Spray® Junior manual prior to spraying.

EZ~Spray® Silicone 20 and 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 20 cures in about 20 minutes while EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials. EZ~Spray® Silicone 20 and 22 silicones are effective at making fast, cost effective vacuum bags for producing composite parts. Newly sprayed or injected bags can be removed from the mold in a matter of minutes and used immediately in production with polyester or epoxy resin systems. The advantage that EZ~Spray® Silicone offers vs. conventional vacuum bagging systems is the speed at which a production-ready silicone bags can be made resulting in significant time and labor savings. Read the EZ~Spray® Junior manual prior to spraying.

Mold Max™ Silicones are tin-cured silicone rubber compounds that have exceptional working properties and library life. Mold Max™ Silicones feature Smooth-On's exclusive "Libra™" catalyst for long library life. Mold Max™ silcones can be pigmented with Silc Pig™ silicone colorants. Pot life for the pourable silicones is 45 minutes and they cure overnight at room temperature. Mold Max™ Silicones will reproduce the finest detail and are suitable for a variety of industrial and art related applications including making molds for reproducing prototypes, furniture, sculpture and architectural elements. Mold Max™ 10, 20, 25 and 30 silicones can be thickened with THI-VEX™ additive for brush-on applications. (Note: THI-VEX™ is NOT compatible with Mold Max™ 40 or 60). Mold Max™ 60 offers highest heat resistance for casting metal (see separate technical bulletin). Mold Max™ Silicones can be used to cast a variety of materials including wax, gypsum, low melt alloys/metals and urethane, epoxy or polyester resins (without using a release agent). Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ silicones. Vacuum degassing mixed material using a vacuum pump and chamber to remove entrapped air is recommended.

Mold Max™ 10T, 15T and 27T silicone are water white translucent tin cured silicone rubber compounds that have exceptional tear strength and working properties. They feature Smooth-On's "Libra™" catalyst for long library life. Mixed 100A:10B by weight, vacuum degassing is recommended for de-airing. Rubber cures overnight at room temperature. Similar in appearance to Smooth-On's premium Dragon Skin™ platinum silicones, Mold Max™ ‘T' silicones are a less costly alternative for creating animatronic skin effects. Mold Max™ ‘T' silicones can be thickened with Thi-Vex™ ii thickener for brush-on application and effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Mold Max™ ‘T’ series silicones are also good for making molds used for casting plaster and wax. NOTE: Mold Max™ ‘T’ series silicones should NOT be used to make molds for casting Crystal Clear™ or Clear Flex™ Series urethanes. Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ 10T, 15T and 27T.

Mold Max™ 14NV and 29NV are tin-catalyzed silicone rubbers that offer low viscosity, fast cure and long library life. Mold Max™ 14NV and 29NV do not require vacuum degassing. Mix ratio is 100A:10B by weight. Pot life is 40 minutes. Cure time of 14NV is 4 hours at room temperature, cure time of 29NV is 6 hours at room temperature. Mold Max™ 14NV and 29NV will reproduce the finest detail and are suitable for a variety of industrial and art related applications including making molds for reproducing prototypes, furniture, sculpture and architectural elements. Cure time can be reduced with Accel-T™ cure accelerator. Mold Max™ 14NV and 29NV can be used to cast a variety of materials including wax, gypsum, low melt alloys/metals and urethane, epoxy or polyester resins. Important; Do not cast concrete into rubber molds made with this product. Concrete will not cure properly and inhibition will result. Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ 14NV and 29NV.

Mold Max™ 10T, 15T and 27T silicone are water white translucent tin cured silicone rubber compounds that have exceptional tear strength and working properties. They feature Smooth-On's "Libra™" catalyst for long library life. Mixed 100A:10B by weight, vacuum degassing is recommended for de-airing. Rubber cures overnight at room temperature. Similar in appearance to Smooth-On's premium Dragon Skin™ platinum silicones, Mold Max™ ‘T' silicones are a less costly alternative for creating animatronic skin effects. Mold Max™ ‘T' silicones can be thickened with Thi-Vex™ ii thickener for brush-on application and effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Mold Max™ ‘T’ series silicones are also good for making molds used for casting plaster and wax. NOTE: Mold Max™ ‘T’ series silicones should NOT be used to make molds for casting Crystal Clear™ or Clear Flex™ Series urethanes. Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ 10T, 15T and 27T.

Mold Max™ Silicones are tin-cured silicone rubber compounds that have exceptional working properties and library life. Mold Max™ Silicones feature Smooth-On's exclusive "Libra™" catalyst for long library life. Mold Max™ silcones can be pigmented with Silc Pig™ silicone colorants. Pot life for the pourable silicones is 45 minutes and they cure overnight at room temperature. Mold Max™ Silicones will reproduce the finest detail and are suitable for a variety of industrial and art related applications including making molds for reproducing prototypes, furniture, sculpture and architectural elements. Mold Max™ 10, 20, 25 and 30 silicones can be thickened with THI-VEX™ additive for brush-on applications. (Note: THI-VEX™ is NOT compatible with Mold Max™ 40 or 60). Mold Max™ 60 offers highest heat resistance for casting metal (see separate technical bulletin). Mold Max™ Silicones can be used to cast a variety of materials including wax, gypsum, low melt alloys/metals and urethane, epoxy or polyester resins (without using a release agent). Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ silicones. Vacuum degassing mixed material using a vacuum pump and chamber to remove entrapped air is recommended.

Mold Max™ Silicones are tin-cured silicone rubber compounds that have exceptional working properties and library life. Mold Max™ Silicones feature Smooth-On's exclusive "Libra™" catalyst for long library life. Mold Max™ silcones can be pigmented with Silc Pig™ silicone colorants. Pot life for the pourable silicones is 45 minutes and they cure overnight at room temperature. Mold Max™ Silicones will reproduce the finest detail and are suitable for a variety of industrial and art related applications including making molds for reproducing prototypes, furniture, sculpture and architectural elements. Mold Max™ 10, 20, 25 and 30 silicones can be thickened with THI-VEX™ additive for brush-on applications. (Note: THI-VEX™ is NOT compatible with Mold Max™ 40 or 60). Mold Max™ 60 offers highest heat resistance for casting metal (see separate technical bulletin). Mold Max™ Silicones can be used to cast a variety of materials including wax, gypsum, low melt alloys/metals and urethane, epoxy or polyester resins (without using a release agent). Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ silicones. Vacuum degassing mixed material using a vacuum pump and chamber to remove entrapped air is recommended.

Mold Max™ 10T, 15T and 27T silicone are water white translucent tin cured silicone rubber compounds that have exceptional tear strength and working properties. They feature Smooth-On's "Libra™" catalyst for long library life. Mixed 100A:10B by weight, vacuum degassing is recommended for de-airing. Rubber cures overnight at room temperature. Similar in appearance to Smooth-On's premium Dragon Skin™ platinum silicones, Mold Max™ ‘T' silicones are a less costly alternative for creating animatronic skin effects. Mold Max™ ‘T' silicones can be thickened with Thi-Vex™ ii thickener for brush-on application and effects. An infinite number of color effects can be achieved by adding Silc Pig™ silicone pigments or Cast Magic™ effects powders. Mold Max™ ‘T’ series silicones are also good for making molds used for casting plaster and wax. NOTE: Mold Max™ ‘T’ series silicones should NOT be used to make molds for casting Crystal Clear™ or Clear Flex™ Series urethanes. Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ 10T, 15T and 27T.

Mold Max™ 14NV and 29NV are tin-catalyzed silicone rubbers that offer low viscosity, fast cure and long library life. Mold Max™ 14NV and 29NV do not require vacuum degassing. Mix ratio is 100A:10B by weight. Pot life is 40 minutes. Cure time of 14NV is 4 hours at room temperature, cure time of 29NV is 6 hours at room temperature. Mold Max™ 14NV and 29NV will reproduce the finest detail and are suitable for a variety of industrial and art related applications including making molds for reproducing prototypes, furniture, sculpture and architectural elements. Cure time can be reduced with Accel-T™ cure accelerator. Mold Max™ 14NV and 29NV can be used to cast a variety of materials including wax, gypsum, low melt alloys/metals and urethane, epoxy or polyester resins. Important; Do not cast concrete into rubber molds made with this product. Concrete will not cure properly and inhibition will result. Important; you must weigh Part A & B components using a gram scale to be successful with Mold Max™ 14NV and 29NV.