| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
RoHS Compliance
|
|
|||
|
Automotive Specifications
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|||
|
--
|
|
|
ASTM D471 |
|
--
|
|
g/cm³
|
ISO 2781 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
|
|
mg
|
ASTM D1044 |
|
Torsion Modulus 2
|
ASTM D1043 | ||
|
-4°F, 74.8 mil
|
|
psi
|
|
|
75°F, 74.8 mil
|
|
psi
|
|
| Elastomers |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Set 3
|
|
%
|
ASTM D412 |
|
Tensile Stress
|
|||
|
100% Strain, 0.0748 in 2
|
|
psi
|
ASTM D412, ISO 37 |
|
100% Strain, 257°F, 0.0748 in 4
|
|
psi
|
ASTM D573, ISO 188 |
|
Tensile Strength
|
|||
|
Yield, 0.0748 in 2
|
|
psi
|
ASTM D412, ISO 37 |
|
Yield, 257°F, 0.0748 in 4
|
|
psi
|
ASTM D573, ISO 188 |
|
Tensile Elongation
|
|||
|
Break, 257°F, 0.0748 in 4
|
|
%
|
ASTM D573, ISO 188 |
|
Break, 0.0748 in 2
|
|
%
|
ASTM D412, ISO 37 |
|
Tear Strength 5, 2 (0.0748 in)
|
|
lbf/in
|
ASTM D624 |
|
Compression Set 6
|
ASTM D395B, ISO 815 | ||
|
75°F, 22.0 hr
|
|
%
|
|
|
212°F, 22.0 hr
|
|
%
|
|
|
Clash-Berg Modulus (-22°F)
|
|
psi
|
ASTM D1043 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Durometer Hardness (Shore A, 0.0748 in, Compression Molded)
|
|
|
ASTM D2240, ISO 868 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Brittleness Temperature
|
|
°F
|
ASTM D746, ISO 812 |
| Aging |
Nominal Value
|
Unit
|
Test Method
|
|
Change in Durometer Hardness in Air 3 (Shore A, 257°F, 168 hr)
|
|
|
ASTM D573, ISO 188 |
|
Change in Volume 3
|
|||
|
81°F, 168 hr, in Reference Fuel B
|
|
%
|
ASTM D471, ISO 1817 |
|
212°F, 168 hr, in ASTM Oil #1
|
|
%
|
ASTM D471 |
|
212°F, 168 hr, in IRM 903 Oil
|
|
%
|
ASTM D471, ISO 1817 |
|
212°F, 168 hr, in Water
|
|
%
|
ASTM D471, ISO 1817 |
|
212°F, 168 hr, in ASTM #1 Oil
|
|
%
|
ISO 1817 |
| Fill Analysis |
Nominal Value
|
Unit
|
Test Method
|
|
Melt Viscosity (374°F, 300 sec^-1)
|
|
Pa·s
|
ASTM D3835 |
| Related Terminology | |||
|
This supplier and product may also be known by these terms: APA, Advanced Polymer Alloys is a division of FerroProduct names can be difficult to match. You may have searched any one of these terms to find this product: Alcryn® 1080 BK, Alcryn 1080 BK, Alcryn® , Alcryn, Alcryn1080BK, 1080 BK, 1080BK, Melt Processable Rubber, MPR, Thermoplastic Elastomer, TPE, APA, MeltProcessableRubber, ThermoplasticElastomer, BK1080
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Weather Resistance, Weather Resistant, High Heat Resistance, Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Fabric Coatings, Fabric Coating, Gaskets, Gasketing, Tubing, Tube, Wire and Cable Applications, Wire & Cable Applications, Flexible Grips.
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Processing (Melt) Temp
|
|
°F
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 2Compression Molded |
| 31.9 mm, Compression Molded |
| 47 days, Compression Molded |
| 5Die C |
| 6Type I pellets, 12.7 mm diameter, plied up from 1.9 mm slabs |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |