Home > Plastics > Materials > Menzolit® > Menzolit® BMC 2600 - Datasheet

Menzolit® BMC 2600 Data Sheet

Thermoset Polyester

18% Glass\Mineral

Supplied by Menzolit Ltd (UK)

View Complete Data Sheet Search 95000+ Data Sheets
Create Your Free Account!
Product Description
Menzolit® BMC 2600 is a bulk moulding compound based on unsaturated polyester resin. The product is glass fibre reinforced and contains mineral fillers. In case of fire the product doesn't melt, neither does it form droplets nor is smoke generation excessive. The material is injection moulded in heated steel moulds. It is recommended to work with chrome plated tools. The product contains no halogens.

Menzolit® BMC 2600 is a special BMC with reduced electrical properties. The glass content is set to a level that combines good mouldability with good strength and stiffness properties. Because of its improved contactivity the product prevents building ups of electrical charges on the surface. At the same time the isolation properties are good enough to provide sufficient isolation. Typical applications are housings and covers in the communications industry, gas or oil exploration industry and mining equipment.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Filler / Reinforcement 
  • Glass\Mineral, 18% Filler by Weight
Features 
  • Antistatic
  • Conductive
  • Flame Retardant
  • Good Moldability
  • Good Stiffness
  • Good Strength
  • Halogen Free
  • High Heat Resistance
  • Low Smoke Emission
Uses 
  • Communication Applications
  • Housings
  • Mining Applications
Forms 
  • BMC - Bulk Molding Compound
Processing Method 
  • Injection Molding
Part Marking Code (ISO 11469)
  • >UP-(MD+GF)71<
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
ISO 1183
Molding Shrinkage
     
-- 2
%
DIN 53464
--
%
ISO 2577
Water Absorption (Saturation, 73°F)
%
ISO 62
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus (Compression Molded)
psi
ISO 527-2
Tensile Stress (Yield, Compression Molded)
psi
ISO 527-2
Flexural Modulus (Compression Molded)
psi
ISO 178
Flexural Strength (Compression Molded)
psi
ISO 178
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength (Compression Molded)
ft·lb/in²
ISO 179
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature (264 psi, Unannealed)
°F
ISO 75-2/A
Continuous Use Temperature
°F
Internal Method
Glass Transition Temperature
°F
DSC
CLTE - Flow
in/in/°F
ISO 11359-2
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
IEC 60093
Volume Resistivity
ohm·cm
IEC 60093
Comparative Tracking Index
V
IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating (0.118 in)
 
UL 94
Glow Wire Ignition Temperature
°F
IEC 60695-2-13
Oxygen Index
%
ISO 4589-2
Additional Information
Nominal Value
Unit
Test Method
Glow Bar
 
IEC 60707-3
Features
Features may also be described by the following terms: Low Smoke Emission, Zero Halogen Content, Halogen Free, High Heat Resistance, Good Strength, Good Stiffness, Good Moldability.
Uses
Uses may also be described by the following terms: Housings, Housing, Communication Applications, Communications.
Available Documents
Processing - Injection Molding (English)
Processing - Injection-Compression (English)
Technical Datasheet (English)
Injection
Nominal Value
Unit
 
Mold Temperature
°F
 
Injection Pressure
psi
 
Notes
1Typical properties: these are not to be construed as specifications.
2Post Molding Shrinkage
 
UL and the UL logo are trademarks of UL LLC © 2014. All Rights Reserved.
The information presented on this datasheet was acquired by UL Prospector from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.