| Product Description | ||||
|
Menzolit® BMC 1100 is a bulk moulding compound based on unsaturated polyester resin. The product is glass fibre reinforced and contains mineral fillers. In case of fire the product doesn't melt, neither does it form droplets nor is smoke generation excessive. The material is compression moulded in heated steel moulds. It is recommended to work with chrome plated tools. The product contains no halogens.
Menzolit® BMC 1100 is a special BMC for high strength application. The glass content is set to a level that provides sufficient mouldability with high strength and stiffness properties. The selection of the resin and glass fibres provide good properties at high mechanical loads even if they are cyclic or impact like. The fire retardancy level HB according to the UL 94 is achieved. Typical applications are functional components for the automotive industry and chemical engineering. The material is especially suited for highly loaded or fast moving components. |
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Filler / Reinforcement
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Automotive Specifications
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
|||
|
Part Marking Code (ISO 11469)
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183 |
|
Molding Shrinkage
|
|||
|
--
|
|
%
|
ISO 2577 |
|
-- 2
|
|
%
|
DIN 53464 |
|
Water Absorption (Saturation, 73°F)
|
|
%
|
ISO 62 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus (Compression Molded)
|
|
psi
|
ISO 527-2 |
|
Tensile Stress (Yield, Compression Molded)
|
|
psi
|
ISO 527-2 |
|
Flexural Modulus (Compression Molded)
|
|
psi
|
ISO 178 |
|
Flexural Strength (Compression Molded)
|
|
psi
|
ISO 178 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Charpy Notched Impact Strength (Compression Molded)
|
|
ft·lb/in²
|
ISO 179 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature (264 psi, Unannealed)
|
|
°F
|
ISO 75-2/A |
|
Max. Continuous Use Temperature
|
|
°F
|
Internal Method |
|
Glass Transition Temperature (DSC)
|
|
°F
|
DSC |
|
CLTE - Flow
|
|
in/in/°F
|
ISO 11359-2 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Surface Resistivity
|
|
ohm
|
IEC 60093 |
|
Volume Resistivity
|
|
ohm·cm
|
IEC 60093 |
|
Comparative Tracking Index
|
|
V
|
IEC 60112 |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating (0.118 in)
|
|
|
UL 94 |
|
Glow Wire Ignition Temperature
|
|
°F
|
IEC 60695-2-13 |
|
Oxygen Index
|
|
%
|
ISO 4589-2 |
| Additional Information |
Nominal Value
|
Unit
|
Test Method
|
|
Glow Bar
|
|
|
IEC 60707-3 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Menzolit® BMC 1100, Menzolit BMC 1100, Menzolit® , Menzolit, MenzolitBMC1100, BMC 1100, BMC1100, Polyester, Thermoset, Polyester Thermoset, Polyester, TS, Polyester TS, Thermoset, TS, PolyesterThermoset, PolyesterTS, 1100BMC
|
|||
| Features | |||
|
Features may also be described by the following terms: Low Smoke Emission, Zero Halogen Content, Halogen Free, High Heat Resistance, Good Strength, Good Stiffness, Good Moldability.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Automotive Applications, Automotive Sector.
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): PSA Peugeot-Citroën (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Mold Temperature
|
|
°F
|
|
|
Injection Pressure
|
|
psi
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 2Post Molding Shrinkage |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |