| Product Description | ||||
|
Parylene D, the third member of the series, is produced from the same dimer as Parylene N modified by the substitution of the chlorine atom for two of the aromatic hydrogens. Parylene D is similar in properties to Parylene C with the added ability to withstand higher use temperatures (up to 125°C).
|
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
RoHS Compliance
|
|
|||
|
Forms
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ASTM D1505 |
|
Water Absorption (24 hr)
|
|
%
|
ASTM D570 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Coefficient of Friction
|
ASTM D1894 | ||
|
vs. Itself - Dynamic
|
|
|
|
|
vs. Itself - Static
|
|
|
|
| Films |
Nominal Value
|
Unit
|
Test Method
|
|
Film Thickness - Tested
|
|
mil
|
|
|
Secant Modulus - MD (2.0 mil)
|
|
psi
|
ASTM D882 |
|
Tensile Strength - MD
|
ASTM D882 | ||
|
Yield, 2.0 mil
|
|
psi
|
|
|
Break, 2.0 mil
|
|
psi
|
|
|
Tensile Elongation - MD
|
ASTM D882 | ||
|
Yield, 2.0 mil
|
|
%
|
|
|
Break, 2.0 mil
|
|
%
|
|
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Rockwell Hardness (R-Scale)
|
|
|
ASTM D785 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Melting Temperature
|
|
°F
|
|
|
CLTE - Flow (77°F)
|
|
in/in/°F
|
ASTM D696 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Surface Resistivity
|
|
ohm
|
ASTM D257 |
|
Volume Resistivity
|
|
ohm·cm
|
ASTM D257 |
|
Dielectric Strength (0.00100 in)
|
|
V/mil
|
ASTM D149 |
|
Dielectric Constant
|
ASTM D150 | ||
|
60 Hz
|
|
|
|
|
1 kHz
|
|
|
|
|
1 MHz
|
|
|
|
|
Dissipation Factor
|
ASTM D150 | ||
|
60 Hz
|
|
|
|
|
1 kHz
|
|
|
|
|
1 MHz
|
|
|
|
| Optical |
Nominal Value
|
Unit
|
Test Method
|
|
Refractive Index
|
|
|
ASTM D542 |
| Additional Information | |||
|
Volume Resistivity, ASTM D257, 23°C, 50% RH: 1.9e17 ohm-cm
Surface Resistivity, ASTM D257, 23°C, 50% RH: 1e16 Nitrogen Gas Permeability, ASTM D1434, 25°C: 1.8 cc-mm/m²-d Oxygen Gas Permeability, ASTM D1434, 25°C: 12.6 cc-mm/m²-d Carbon Dioxide Gas Permeability, ASTM D1434, 25°C: 5.1 cc-mm/m²-d Hydrogen Gas Permeability, ASTM D1434, 25°C: 94.5 cc-mm/m²-d Moisture Vapor Transmission, ASTM E96, 90% RH, 37°C: 0.09 g-mm-m²-d T5 point, Secant Modulus-Temperature Curve, Modulus=690 MPa: 125°C T4 point, Secant Modulus-Temperature Curve, Modulus=70 MPa: 240°C Continuous Service Temperature:100°C Short-Term Service Temperature: 120°C Linear Coef. of Thermal Expan., ASTM D696, 25°C: 30 to 80 ppm |
|||
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Parylene D, Parylene , ParyleneD, Polyparaxylylene, PPX, SCS
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Adhesion, Good Electrical Properties, Radiation Resistant, Gamma Stable, Gamma Resistant, Radiation Stable, High Heat Resistance.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Printed Circuit Boards, Medical Applications.
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |