| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Agency Ratings
|
|
|||
|
RoHS Compliance
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|||
|
--
|
|
|
ASTM D792 |
|
--
|
|
g/cm³
|
ISO 1183 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Taber Abrasion Resistance
|
ASTM D1044 | ||
|
1000 g, CS-17 Wheel
|
|
mg
|
|
|
1000 g, CS-18 Wheel
|
|
mg
|
|
| Elastomers |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Set
|
|
%
|
ASTM D412 |
|
Tensile Stress (100% Strain)
|
|
psi
|
ASTM D412, ISO 37 |
|
Tensile Strength (Yield)
|
|
psi
|
ASTM D412, ISO 37 |
|
Tensile Elongation (Break)
|
|
%
|
ASTM D412, ISO 37 |
|
Tear Strength
|
|||
|
75°F 2
|
|
lbf/in
|
ASTM D624 |
|
75°F
|
|
lbf/in
|
ISO 34-1 |
|
Compression Set
|
|||
|
75°F, 22.0 hr
|
|
%
|
ASTM D395A |
|
158°F, 22.0 hr
|
|
%
|
ASTM D395A |
|
212°F, 22.0 hr
|
|
%
|
ASTM D395A |
|
75°F, 22.0 hr 3
|
|
%
|
ISO 815 |
|
158°F, 22.0 hr 3
|
|
%
|
ISO 815 |
|
212°F, 22.0 hr 3
|
|
%
|
ISO 815 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Durometer Hardness (Shore A)
|
|
|
ASTM D2240, ISO 868 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Brittleness Temperature
|
|
°F
|
ASTM D746, ISO 812 |
| Aging |
Nominal Value
|
Unit
|
Test Method
|
|
Change in Tensile Strength in Air
|
|||
|
257°F, 168 hr
|
|
%
|
ASTM D573, ISO 188 |
|
100% Strain, 257°F, 168 hr
|
|
%
|
ASTM D573 |
|
100% Strain 257°F, 168 hr
|
|
%
|
ISO 188 |
|
Change in Ultimate Elongation in Air (257°F, 168 hr)
|
|
%
|
ASTM D573, ISO 188 |
|
Change in Volume
|
|||
|
212°F, 168 hr, in ASTM Oil #1
|
|
%
|
ASTM D471 |
|
212°F, 168 hr, in IRM 903 Oil #3
|
|
%
|
ASTM D471 |
|
212°F, 168 hr, in Water
|
|
%
|
ASTM D471, ISO 1817 |
|
212°F, 168 hr, in ASTM #1 Oil
|
|
%
|
ISO 1817 |
|
212°F, 56640 hr, in IRM 903 Oil #3
|
|
%
|
ISO 1817 |
| Fill Analysis |
Nominal Value
|
Unit
|
Test Method
|
|
Apparent Viscosity (374°F, 300 sec^-1)
|
|
Pa·s
|
ASTM D3835 |
| Related Terminology | |||
|
This supplier and product may also be known by these terms: APA, Advanced Polymer Alloys is a division of FerroProduct names can be difficult to match. You may have searched any one of these terms to find this product: Alcryn® 2360 NC, Alcryn 2360 NC, Alcryn® , Alcryn, Alcryn2360NC, 2360 NC, 2360NC, Melt Processable Rubber, MPR, Thermoplastic Elastomer, TPE, APA, MeltProcessableRubber, ThermoplasticElastomer, NC2360
|
|||
| Agency Ratings | |||
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Processing (Melt) Temp
|
|
°F
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 2Die C |
| 3Type A |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |