| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Uses
|
|
|||
|
Agency Ratings
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Mass-Flow Rate (MFR)
|
ISO 1133 | ||
|
190°C/2.16 kg
|
|
g/10 min
|
|
|
190°C/5.0 kg
|
|
g/10 min
|
|
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus (0.0787 in, Compression Molded)
|
|
psi
|
ISO 527-2/1BA/50 |
|
Tensile Stress (Yield, 0.0787 in, Compression Molded)
|
|
psi
|
ISO 527-2/1BA/50 |
|
Tensile Strain (Yield, 0.0787 in, Compression Molded)
|
|
%
|
ISO 527-2/1BA/50 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Charpy Notched Impact Strength
|
ISO 179/1eA | ||
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Shore Hardness (Shore D, 15 sec, Compression Molded)
|
|
|
ISO 868 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature
|
|||
|
66 psi, Unannealed
|
|
°F
|
ISO 75-2/B |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
|
Vicat Softening Temperature
|
|
°F
|
ISO 306/B50 |
| Additional Information | |||
|
OIT 210°C, EN 728: >20 min
MRS Classification, ISO 12162: 10 MPa Melting Point, SABIC Method, DSC: 124 to 128°C RAL Number: 5005 Color Code: 65307 |
|||
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® Vestolen A 6060R b, SABIC Vestolen A 6060R b, SABIC® Vestolen A , SABIC Vestolen A, SABICVestolenA6060Rb, SABICVestolenA, A 6060 R b, A6060R b, A6060, 6060 R b, A6060Rb, 6060R b, 6060R, Rb, 6060Rb, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, SABIC, PolyethyleneHighDensity, R6060, 6060A
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Piping, Pipe.
|
|||
| Agency Ratings | |||
|
This plastic material has 2 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1), EEC (1).
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |