| Product Description | ||||
|
This grade has been specially developed for use in thin-walled, antistatic containers. The material has outstanding flow properties and a high stiffness, enabling high production rates. Special characteristics are low tendency for warpage, high lot to lot consistency, good contact transparency and high gloss. It is formulated with a combined processing and antistatic additive package.
|
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Additive
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Automotive Specifications
|
|
|||
|
UL File Number
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Mass-Flow Rate (MFR)
|
ISO 1133 | ||
|
230°C/2.16 kg
|
|
g/10 min
|
|
|
230°C/5.0 kg
|
|
g/10 min
|
|
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Stress
|
ISO 527-2 | ||
|
Yield
|
|
psi
|
|
|
Break
|
|
psi
|
|
|
Tensile Strain (Break)
|
|
%
|
ISO 527-2 |
|
Flexural Modulus
|
|
psi
|
ASTM D790 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Charpy Notched Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 179 |
|
Notched Izod Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 180/4A |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Shore Hardness (Shore D)
|
|
|
ISO 868 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature
|
|||
|
66 psi, Unannealed
|
|
°F
|
ISO 75-2/B |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
|
Vicat Softening Temperature
|
|||
|
--
|
|
°F
|
ISO 306/A |
|
--
|
|
°F
|
ISO 306/B |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: SABIC® PP 579S, SABIC PP 579S, SABIC® PP , SABIC PP, SABICPP579S, SABICPP, PP 579 S, PP579S, PP579, PP, 579 S, 579S, Polypropylene Homopolymer, PP Homopolymer, Polypropylene, SABIC, PolypropyleneHomopolymer, PPHomopolymer, S579, 579PP
|
|||
| Features | |||
|
Features may also be described by the following terms: High Stiffness, Low Warpage, Low Warp, High Gloss, Good Flow, Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Thin-Walled Containers, Thin-Walled Container, Thin-Wall Containers, Thin-Wall Container, Thinwall Containers, Thinwall Container.
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): IMDS (1).
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |