Home > Plastics > Materials > LongLite > LongLite T375J - Datasheet

LongLite T375J Datasheet

Phenolic

Supplied by Dowell Trading Company Ltd.

View Complete Data Sheet Search 95000+ Data Sheets
Create Your Free Account! or Login
Product Description
LongLite T375J is a Phenolic product. It can be processed by injection molding and is available in North America. Typical application: Electrical/Electronic Applications.

Characteristics include:
  • Flame Rated
  • Heat Resistant
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Features 
  • Medium Heat Resistance
Uses 
  • Electrical/Electronic Applications
Appearance 
  • Black
Forms 
  • Pellets
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
ASTM D792
Molding Shrinkage - Flow
    ASTM D955
Compression Molded
in/in
 
Injection Molded
in/in
 
Transfer Molded
in/in
 
Water Absorption (Equilibrium)
%
ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength
psi
ASTM D638
Flexural Strength
psi
ASTM D790
Compressive Modulus
psi
ASTM D695
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength
ft·lb/in
ASTM D256
Notched Izod Impact
ft·lb/in
ASTM D256
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load (264 psi, Unannealed)
°F
ASTM D648
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
ASTM D257
Volume Resistivity
ohm·cm
ASTM D257
Dielectric Strength
V/mil
ASTM D149
Arc Resistance
sec
ASTM D495
Comparative Tracking Index (CTI)
 
UL 746
Flammability
Nominal Value
Unit
Test Method
Flame Rating (0.0311 in)
 
UL 94
Additional Information
The value listed for Tensile Strength, ASTM D638, was tested in accordance to ASTM D651 test methods.

Heat Resistance, ASTM D648, 2 hours: 200°C
Insulation Resistance, ASTM D257, After Boiling: 1x10^9
ASTM Grade, ASTM D700: 13
Features
Features may also be described by the following terms: Medium Heat Resistance.
Uses
Uses may also be described by the following terms: Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
Injection
Nominal Value
Unit
 
Rear Temperature
°F
 
Front Temperature
°F
 
Mold Temperature
°F
 
Screw Speed
rpm
 
Injection Notes
For Stiff to Medium Flow: Weight (g)/shot: under 300; Mold Temperature: 160 to 180°C; Front Temperature: 85 to 95°C; Rear Temperature: 60 to 80°C; Screw Revolution: 40 to 60 rpm; Cure Time: 6 to 10 seconds per 1 mm of mold thickness.

For Soft Flow: Weight (g)/shot: above 300; Mold Temperature: 165 to 190°C; Front Temperature: 85 to 95°C; Rear Temperature: 55 to 75°C; Screw Revolution: 40 to 60 rpm; Cure Time: 6 to 10 seconds per 1 mm of mold thickness.
Notes
1Typical properties: these are not to be construed as specifications.
 
UL and the UL logo are trademarks of UL LLC © 2014. All Rights Reserved.
The information presented on this datasheet was acquired by UL Prospector from the producer of the material. UL Prospector makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.