| Product Description | ||||
|
HMA 016 is a HDPE grade, characterized by fast cycling and good impact strength. It has high gloss and high dimensional stability.
|
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Additive
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
|
|
g/10 min
|
ASTM D1238 |
|
Environmental Stress-Cracking Resistance (122°F, 10% Igepal)
|
|
hr
|
ASTM D1693 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Stress (Yield)
|
|
psi
|
ISO 527-2/1A/50 |
|
Tensile Strain
|
ISO 527-2/1A/50 | ||
|
Yield
|
|
%
|
|
|
Break
|
|
%
|
|
|
Flexural Modulus
|
|
psi
|
ISO 178 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact Strength
|
|
ft·lb/in²
|
ISO 180/1A |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature (66 psi, Unannealed)
|
|
°F
|
ISO 75-2/B |
|
Peak Melting Temperature
|
|
°F
|
ASTM D3418 |
| Additional Information | |||
|
The molded properties were measured on 4 mm (157.5 mil) thick injection molded specimen based on ISO 294-1.
Heat Deflection temperature sample preparation, injection based on ISO1872. Tested flatwise position with specimen size of 80mm x 10mm x 4mm. ESCR was measured on 2 mm (78.7 mil) thick compression molded plate (F50, 10 % Igepal, 50°C, 122°F) |
|||
| Legal Statement | |||
|
Contact your ExxonMobil Chemical Customer Service Representative for potential food contact application compliance (e.g. FDA, EU, HPFB).
This product is not intended for use in medical applications and should not be used in any such applications. |
|||
| Related Terminology | |||
|
This supplier and product may also be known by these terms: Exxon, Exxon Mobil, Exxon Mobile, Advanced Elastomer Systems, AESProduct names can be difficult to match. You may have searched any one of these terms to find this product: ExxonMobil™ HDPE HMA 016, ExxonMobil HDPE HMA 016, ExxonMobil™ HDPE , ExxonMobil HDPE, ExxonMobilHDPEHMA016, ExxonMobilHDPE, HDPEHMA 016, HDPE, HDPEHMA016, HMA 016, HMA016, Polyethylene, High Density, Polyethylene High Density, Polyethylene, PE, ExxonMobil, PolyethyleneHighDensity, 016HMA, 016HDPEHMA
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |