| Product Description | ||||
|
Amodel AT-1001L is an unreinforced, impact modified polyphthalamide (PPA) resin that exhibits exceptional impact strength at temperatures ranging from room temperature to as low as -40°F (-40°C), which suggests possible applications in ski boots and hockey skates.
In addition, its chemical and wear resistance, combined with good mechanical properties, make Amodel AT-1001L resin a prime candidate for applications such as anti-friction and wear resistant components, chemical, oil field, automotive and safety equipment.
|
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Additive
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
RoHS Compliance
|
|
|||
|
Automotive Specifications
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
|||
|
Multi-Point Data
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183/A |
|
Molding Shrinkage
|
ASTM D955 | ||
|
Flow
|
|
in/in
|
|
|
Across Flow
|
|
in/in
|
|
|
Water Absorption (24 hr)
|
|
%
|
ASTM D570 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus
|
|
psi
|
ASTM D638 |
|
Tensile Strength (Break)
|
|
psi
|
ASTM D638 |
|
Tensile Elongation
|
ASTM D638 | ||
|
Yield
|
|
%
|
|
|
Break
|
|
%
|
|
|
Flexural Modulus
|
|
psi
|
ASTM D790 |
|
Flexural Strength
|
|
psi
|
ASTM D790 |
|
Poisson's Ratio
|
|
|
ASTM E132 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact
|
ASTM D256 | ||
|
-40°F
|
|
ft·lb/in
|
|
|
73°F
|
|
ft·lb/in
|
|
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Deflection Temperature Under Load (264 psi, Annealed, 0.125 in)
|
|
°F
|
ASTM D648 |
|
Melting Temperature
|
|
°F
|
|
| Additional Information | |||
|
Penetration Impact, ASTM D3763, 73°F, Maximum Load: 1100 lbs
Penetration Impact, ASTM D3763, 73°F, Total Energy Absorbed: 40 ft-lbs Penetration Impact, ASTM D3763, 73°F, Energy to Maximum Load: 30 ft-lbs Penetration Impact, ASTM D3763, -10°F, Total Energy Absorbed: 40 ft-lbs Penetration Impact, ASTM D3763, -10°F, Maximum Load: 1260 lbs Penetration Impact, ASTM D3763, -10°F, Energy to Maximum Load: 30 ft-lbs |
|||
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Amodel® AT-1001L, Amodel AT1001L, Amodel® , Amodel, AmodelAT1001L, AT, AT 1001 L, AT-1001L, AT1001L, AT:1001L, AT/1001L, AT+1001L, AT_1001L, AT 1001L, AT1001, 1001L, Polyphthalamide, PPA, Polyamide, Nylon, Solvay Specialty, 1001AT
|
|||
| Features | |||
|
Features may also be described by the following terms: Low Temperatuer Impact Resistance, Low Temp Impact Resistance, Good Chemical Resistance, Chemical Resistant, Hot Water Moldable, Low Warpage, Low Warp, Good Wear Resistance, Wear Resistant.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Machine Parts, Mechanical Parts, Machine/Mechanical Parts, Housings, Housing, Industrial Parts, Automotive Applications, Automotive Sector, Oil Applications, Gas Applications.
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): ASTM (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
|
°F
|
|
|
Drying Time
|
|
hr
|
|
|
Suggested Max Moisture
|
|
%
|
|
|
Hopper Temperature
|
|
°F
|
|
|
Rear Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Processing (Melt) Temp
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |