Home > Plastics > Materials > VALOX™ > VALOX™ 732E resin - Datasheet

VALOX™ 732E resin Datasheet

Polybutylene Terephthalate

30% Glass\Mineral

Supplied by SABIC Innovative Plastics

View Complete Data Sheet Search 95000+ Data Sheets
Create Your Free Account! or Login
Product Description
30% glass/mineral reinforced, excellent thermal performance, low shrinkage and warp. Easy flow.
General  
Material Status 
  • Commercial: Active
Availability 
  • North America
Filler / Reinforcement 
  • Glass\Mineral, 30% Filler by Weight
Features 
  • Good Flow
  • Low Shrinkage
  • Low Warpage
Automotive Specifications 
 
Processing Method 
  • Injection Molding
Multi-Point Data 
  • Coefficient of Thermal Expansion vs. Temperature (ASTM E831)
  • Elastic Modulus vs Temperature (ASTM D4065)
  • Flexural DMA (ASTM D4065)
  • Instrumented Impact (Energy) (ASTM D3763)
  • Instrumented Impact (Load) (ASTM D3763)
  • Pressure-Volume-Temperature (PVT - Zoller Method)
  • Shear DMA (ASTM D4065)
  • Specific Heat vs. Temperature (ASTM D3417)
  • Tensile Creep (ASTM D2990)
  • Tensile Fatigue
  • Tensile Stress vs. Strain (ASTM D638)
  • Thermal Conductivity vs. Temperature (ASTM E1530)
  • Viscosity vs. Shear Rate (ASTM D3835)
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
ASTM D792
Specific Volume
in³/lb
ASTM D792
Molding Shrinkage
    Internal Method
Flow  2
in/in
 
Flow  3
in/in
 
Across Flow  3
in/in
 
Across Flow  4
in/in
 
Water Absorption (24 hr)
%
ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 5 (Break)
psi
ASTM D638
Tensile Elongation 5 (Break)
%
ASTM D638
Flexural Modulus 6 (1,97 in Span)
psi
ASTM D790
Flexural Strength 6 (Break, 1,97 in Span)
psi
ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
ASTM D256
Unnotched Izod Impact (73°F)
ft·lb/in
ASTM D4812
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
    ASTM D648
66 psi, Unannealed, 0,252 in
°F
 
264 psi, Unannealed, 0,252 in
°F
 
CLTE - Flow
    ASTM E831
-40 to 104°F
in/in/°F
 
140 to 280°F
in/in/°F
 
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
ASTM D257
Dielectric Strength (0,126 in, in Oil)
V/mil
ASTM D149
Dielectric Constant
    ASTM D150
50 Hz
 
 
60 Hz
 
 
1 MHz
 
 
Dissipation Factor
    ASTM D150
50 Hz
 
 
60 Hz
 
 
1 MHz
 
 
Related Terminology
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland
Features
Features may also be described by the following terms: Good Flow, Low Warpage, Low Warp, Low Shrinkage.
Automotive Specifications
This plastic material has approval for 2 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (2).
Available Documents
Technical Datasheet
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Drying Time, Maximum
hr
 
Suggested Max Moisture
%
 
Suggested Shot Size
%
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Nozzle Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Back Pressure
psi
 
Screw Speed
rpm
 
Vent Depth
in
 
Notes
1Typical properties: these are not to be construed as specifications.
23.2 to 4.6 mm
31.5 to 3.2 mm
43.2-4.6 mm
5Type I, 0,20 in/min
60,051 in/min
 
UL and the UL logo are trademarks of UL LLC © 2014. All Rights Reserved.
The information presented on this datasheet was acquired by UL Prospector from the producer of the material. UL Prospector makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.