Home > Plastics > Materials > GELOY™ > GELOY™ HRA170 resin - Datasheet

GELOY™ HRA170 resin Data Sheet

Acrylonitrile Styrene Acrylate + PC

Supplied by SABIC Innovative Plastics Europe

View Complete Data Sheet Search 95000+ Data Sheets
Create Your Free Account!
Product Description
GELOY HRA170 is a high heat resistant ASA+PC. It shows high impact retention, which can be positioned for various outdoor and indoor applications requiring superior heat aging properties and colour stability.
General  
Material Status 
  • Commercial: Active
Availability 
  • Europe
Features 
  • Good Color Stability
  • Good Heat Aging Resistance
  • High Heat Resistance
  • High Impact Resistance
 
Uses 
  • Outdoor Applications
RoHS Compliance 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Density
g/cm³
ISO 1183
Melt Volume-Flow Rate (MVR) (260°C/5.0 kg)
in³/10min
ISO 1133
Molding Shrinkage - Flow  2
in/in
Internal Method
Water Absorption
    ISO 62
Saturation, 73°F
%
 
Equilibrium, 73°F, 50% RH
%
 
Mechanical
Nominal Value
Unit
Test Method
Tensile Modulus
psi
ISO 527-2/1
Tensile Stress
     
Yield
psi
ISO 527-2/5
Yield
psi
ISO 527-2/50
Break
psi
ISO 527-2/5
Break
psi
ISO 527-2/50
Tensile Strain
     
Yield
%
ISO 527-2/5
Yield
%
ISO 527-2/50
Break
%
ISO 527-2/5
Break
%
ISO 527-2/50
Flexural Modulus 3
psi
ISO 178
Flexural Strength 3, 4
psi
ISO 178
Taber Abrasion Resistance (1000 Cycles, 1000 g, CS-17 Wheel)
mg
Internal Method
Impact
Nominal Value
Unit
Test Method
Charpy Notched Impact Strength 5
    ISO 179/1eA
-22°F
ft·lb/in²
 
73°F
ft·lb/in²
 
Notched Izod Impact Strength 6
    ISO 180/1A
-22°F
ft·lb/in²
 
73°F
ft·lb/in²
 
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
ISO 2039-2
Ball Indentation Hardness (H 358/30)
psi
ISO 2039-1
Thermal
Nominal Value
Unit
Test Method
Heat Deflection Temperature 7
     
66 psi, Unannealed, 3,94 in Span
°F
ISO 75-2/Be
264 psi, Unannealed, 3,94 in Span
°F
ISO 75-2/Ae
Vicat Softening Temperature
     
--
°F
ISO 306/B50
--
°F
ISO 306/B120
CLTE - Flow (73 to 140°F)
in/in/°F
ISO 11359-2
Thermal Conductivity
Btu·in/hr/ft²/°F
ISO 8302
Electrical
Nominal Value
Unit
Test Method
Surface Resistivity
ohm
IEC 60093
Volume Resistivity
ohm·cm
IEC 60093
Electric Strength (0,126 in, in Oil)
V/mil
IEC 60243-1
Relative Permittivity (1 MHz)
 
IEC 60250
Dissipation Factor (1 MHz)
 
IEC 60250
Comparative Tracking Index
V
IEC 60112
Flammability
Nominal Value
Unit
Test Method
Flame Rating (0,0630 in, Testing by SABIC)
 
UL 94
Glow Wire Flammability Index (0,126 in)
°F
IEC 60695-2-12
Oxygen Index
%
ISO 4589-2
Related Terminology
This supplier and product may also be known by these terms: GE Plastics Europe, LNP Engineering Plastics, GE Polymerland Europe, GE Polymerland, GE Plastics
Features
Features may also be described by the following terms: Good Heat Aging Resistance, High Heat Resistance, High Impact Resistance, Good Color Stability.
Available Documents
Technical Datasheet
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Suggested Max Moisture
%
 
Hopper Temperature
°F
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Nozzle Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Notes
1Typical properties: these are not to be construed as specifications.
2Tensile Bar
30,079 in/min
4Yield
580*10*4 sp=62mm
680*10*4
7120*10*4 mm
 
UL and the UL logo are trademarks of UL LLC © 2014. All Rights Reserved.
The information presented on this datasheet was acquired by UL Prospector from the producer of the material. UL Prospector makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.