| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Automotive Specifications
|
|
|||
|
Forms
|
|
|||
|
Multi-Point Data
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Mass-Flow Rate (MFR) (220°C/10.0 kg)
|
|
g/10 min
|
ISO 1133 |
|
Melt Volume-Flow Rate (MVR)
|
ISO 1133 | ||
|
200°C/5.0 kg
|
|
in³/10min
|
|
|
220°C/10.0 kg
|
|
in³/10min
|
|
|
Molding Shrinkage
|
|
%
|
ISO 294-4 |
|
Water Absorption (Saturation, 73°F)
|
|
%
|
ISO 62 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus
|
|
psi
|
ISO 527-2 |
|
Tensile Stress (Yield, 73°F)
|
|
psi
|
ISO 527-2 |
|
Tensile Strain (Yield, 73°F)
|
|
%
|
ISO 527-2 |
|
Flexural Strength
|
|
psi
|
ISO 178 |
| Films |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Elongation - MD (Break)
|
|
%
|
No Standard |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Charpy Notched Impact Strength
|
ISO 179 | ||
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Charpy Unnotched Impact Strength
|
ISO 179 | ||
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Notched Izod Impact 2
|
ISO 180 | ||
|
-22°F, 0.157 in
|
|
ft·lb/in
|
|
|
73°F, 0.157 in
|
|
ft·lb/in
|
|
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Ball Indentation Hardness
|
|
psi
|
ISO 2039-1 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature
|
|||
|
66 psi, Annealed
|
|
°F
|
ISO 75-2/Bf |
|
264 psi, Annealed
|
|
°F
|
ISO 75-2/Af |
|
Vicat Softening Temperature
|
|||
|
--
|
|
°F
|
ISO 306/B50 |
|
--
|
|
°F
|
ISO 306/B120 |
|
CLTE - Flow
|
|
in/in/°F
|
ISO 11359-2 |
|
Thermal Conductivity
|
|
Btu·in/hr/ft²/°F
|
DIN 52612 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Surface Resistivity
|
|
ohm
|
IEC 60093 |
|
Volume Resistivity
|
|
ohm·cm
|
IEC 60093 |
|
Dielectric Constant (100 Hz)
|
|
|
IEC 60250 |
|
Dissipation Factor
|
IEC 60250 | ||
|
100 Hz
|
|
|
|
|
1 MHz
|
|
|
|
| Optical |
Nominal Value
|
Unit
|
Test Method
|
|
Yellowness Index
|
|
YI
|
ASTM D1925 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Terluran® GP-22, Terluran GP22, Terluran® , Terluran, TerluranGP22, GP, GP-22, GP22, GP:22, GP/22, GP+22, GP_22, GP 22, Acrylonitrile Butadiene Styrene, ABS, Styrolution, AcrylonitrileButadieneStyrene, 22GP
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 7 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): FORD (3), PSA Peugeot-Citroën (1), CHRYSLER (1), GM (2).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
|
°F
|
|
|
Drying Time
|
|
hr
|
|
|
Processing (Melt) Temp
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
| Injection Notes | |||
|
Injection Velocity: 200 mm/s
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 20.25 mm Notch Radius |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |