| Product Description | |
|
The viscosity of KE-1955 A/B is low enough to allow easy pumping through most injection molding systems.
Product features include rapid cure time at elevated temperatures, long pot life at room temperature. Typical applications include anode caps, and other electrical parts. Recommended storage of this compound is at or below 90°F and in a dry area. If stored as recommended, KE-1955 A/B will have a shelf life of at least 6 months from the date of shipment. Color A Component: Black B Component: Black |
|
| General | |
|
Material Status
|
|
|
Availability
|
|
|
Features
|
|
|
Uses
|
|
|
Appearance
|
|
|
Forms
|
|
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|
|
ASTM D792 |
| Elastomers |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength (Yield)
|
|
psi
|
ASTM D412 |
|
Tensile Elongation (Break)
|
|
%
|
ASTM D412 |
|
Tear Strength
|
|
lbf/in
|
ASTM D624 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Durometer Hardness (Shore A)
|
|
|
ASTM D2240 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Volume Resistivity
|
|
ohm·cm
|
ASTM D257 |
|
Dielectric Strength
|
|
V/mil
|
ASTM D149 |
| Thermoset |
Nominal Value
|
Unit
|
Test Method
|
|
Pot Life (77°F)
|
|
min
|
|
|
Shelf Life (90°F)
|
|
wk
|
|
|
Thermoset Mix Viscosity
|
|
cP
|
ASTM D2393 |
|
Demold Time (248°F)
|
|
min
|
|
|
Post Cure Time (302°F)
|
|
hr
|
|
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Shincor LIM KE-1955 A/B, Shincor LIM KE1955 AB, Shincor LIM , ShincorLIMKE1955AB, ShincorLIM, LIMKE 1955 A B, KE, LIMKE-1955 A/B, LIMKE1955 AB, LIMKE-1955 A:B, LIMKE-1955 A+B, LIMKE-1955 A-B, LIMKE-1955 A_B, LIMKE-1955 A B, LIMKE:1955 A/B, LIMKE/1955 A/B, LIMKE+1955 A/B, LIMKE_1955 A/B, LIMKE 1955 A/B, LIMKE1955, LIMKE, KE 1955 A B, LIMKE1955AB, LIMKE1955 A_B, LIMKE1955 A B, LIMKE_1955 AB, LIMKE 1955 AB, KE-1955 A/B, KE1955 AB, KE-1955 A:B, KE-1955 A+B, KE-1955 A-B, KE-1955 A_B, KE-1955 A B, KE:1955 A/B, KE/1955 A/B, KE+1955 A/B, KE_1955 A/B, KE 1955 A/B, KE1955, 1955A, AB, LIMKE1955A_B, LIMKE_1955AB, KE1955AB, KE1955 A_B, KE1955 A B, KE_1955 AB, KE 1955 AB, KE1955A_B, KE_1955AB, Silicone, Shincor Sil, 1955KE, 1955LIMKE
|
|||
| Features | |||
|
Features may also be described by the following terms: Heat Cure.
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |