Home > Plastics > Materials > VALOX™ > VALOX™ 310 resin - Datasheet

VALOX™ 310 resin Data Sheet

Polybutylene Terephthalate

Supplied by SABIC Innovative Plastics

View Complete Data Sheet Search 96000+ Data Sheets
Create Your Free Account!
Product Description
VALOX™ 
310 resin
Unreinforced, general purpose. Typical viscosity 5000-7000.
VALOX™ 
310 resin
Unreinforced, general purpose. Typical viscosity 5000-7000.
General VALOX™ 
310 resin
VALOX™ 
310 resin
Material Status 
  • Commercial: Active
  • Commercial: Active
Availability 
  • North America
  • Asia Pacific
Features 
  • General Purpose
  • General Purpose
Uses 
  • General Purpose
  • General Purpose
Automotive Specifications 
--
Processing Method 
  • Injection Molding
  • Injection Molding
Multi-Point Data 
  • Coefficient of Thermal Expansion vs. Temperature (ASTM E831)
  • Elastic Modulus vs Temperature (ASTM D4065)
  • Flexural DMA (ASTM D4065)
  • Pressure-Volume-Temperature (PVT - Zoller Method)
  • Shear DMA (ASTM D4065)
  • Specific Heat vs. Temperature (ASTM D3417)
  • Tensile Creep (ASTM D2990)
  • Tensile Fatigue
  • Tensile Stress vs. Strain (ASTM D638)
  • Thermal Conductivity vs. Temperature (ASTM E1530)
  • Viscosity vs. Shear Rate (ASTM D3835)
--
Physical VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Specific Gravity
 
ASTM D792
Specific Volume
in³/lb
ASTM D792
Molding Shrinkage
      Internal Method
Flow  2
in/in
 
Flow  3
in/in
 
Across Flow  2
in/in
 
Across Flow  3
in/in
 
Water Absorption (24 hr)
%
ASTM D570
Mechanical VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Tensile Strength 4
      ASTM D638
Yield
psi
 
Break
psi
 
Tensile Elongation 4 (Break)
%
ASTM D638
Flexural Modulus 5 (1.97 in Span)
psi
ASTM D790
Flexural Strength 5
      ASTM D790
Yield, 1.97 in Span
psi
 
Break, 1.97 in Span
psi
 
Impact VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Notched Izod Impact (73°F)
ft·lb/in
ASTM D256
Unnotched Izod Impact (73°F)
ft·lb/in
ASTM D4812
Gardner Impact
      ASTM D3029
73°F 6
in·lb
 
73°F
in·lb
 
Hardness VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Rockwell Hardness (R-Scale)
 
ASTM D785
Thermal VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Deflection Temperature Under Load
      ASTM D648
66 psi, Unannealed, 0.252 in
°F
 
264 psi, Unannealed, 0.252 in
°F
 
CLTE - Flow
      ASTM E831
-40 to 104°F
in/in/°F
 
140 to 280°F
in/in/°F
 
RTI Elec
°F
UL 746
RTI Imp
°F
UL 746
RTI Str
°F
UL 746
Electrical VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Volume Resistivity
ohm·cm
ASTM D257
Dielectric Strength
      ASTM D149
0.0630 in, in Air
V/mil
 
0.0630 in, in Oil
V/mil
 
0.126 in, in Air
V/mil
 
0.126 in, in Oil
V/mil
 
Dielectric Constant
      ASTM D150
100 Hz
 
 
1 MHz
 
 
Dissipation Factor
      ASTM D150
100 Hz
 
 
1 MHz
 
 
Arc Resistance 7
 
ASTM D495
Comparative Tracking Index (CTI)
 
UL 746
High Voltage Arc Tracking Rate (HVTR)
 
UL 746
Flammability VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Flame Rating (0.0580 in)
 
UL 94
Fill Analysis VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
Test Method
Melt Viscosity
Pa·s
Internal Method
Related Terminology
VALOX™ 
310 resin
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics, GE Polymerland
VALOX™ 
310 resin
This supplier and product may also be known by these terms: GE Plastics, LNP Engineering Plastics
Automotive Specifications
VALOX™ 
310 resin
This plastic material has approval for 2 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): CHRYSLER (2).
Available Documents
VALOX™ 
310 resin
Technical Datasheet
VALOX™ 
310 resin
Technical Datasheet
Injection VALOX™ 
310 resin
VALOX™ 
310 resin
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Drying Time, Maximum
hr
 
Suggested Max Moisture
%
 
Suggested Shot Size
%
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Nozzle Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Back Pressure
psi
 
Screw Speed
rpm
 
Vent Depth
in
 
Notes
1Typical properties: these are not to be construed as specifications.
22.3 to 4.6 mm
30.75 to 2.3 mm
4Type I, 2.0 in/min
50.051 in/min
6Modified
7Tungsten Electrode
 
UL and the UL logo are trademarks of UL LLC © 2014. All Rights Reserved.
The information presented on this datasheet was acquired by UL Prospector from the producer of the material. UL Prospector makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.