| Product Description | ||||
|
ASTALON™ S1000UR / S1001UR / S1003UR are the medium viscosity (low/medium melt flow) grades in the ASTALON™ range and are well suited to general purpose injection moulding applications which require a mould release agent (R) and UV stabilisation (U). Offering an exceptional combination of transparency, toughness, heat resistance, flame retardancy and processability, typical applications include automotive taillight housings and safety helmet visors.
Note: [ Standard grade = S1000UR ] / [ FDA approved = S1001UR ] / [ Steam resistant = S1003UR ]. |
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Additive
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Processing Method
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR) (300°C/1.2 kg)
|
|
g/10 min
|
ASTM D1238 |
|
Molding Shrinkage - Flow (0.118 in)
|
|
in/in
|
ASTM D955 |
|
Water Absorption (24 hr)
|
|
%
|
ASTM D570 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength 2 (0.126 in)
|
|
psi
|
ASTM D638 |
|
Tensile Elongation 2 (Break, 0.126 in)
|
|
%
|
ASTM D638 |
|
Flexural Modulus 3 (0.252 in)
|
|
psi
|
ASTM D790 |
|
Flexural Strength 3 (0.252 in)
|
|
psi
|
ASTM D790 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact (0.126 in)
|
|
ft·lb/in
|
ASTM D256 |
|
Gardner Impact (0.126 in)
|
|
in·lb
|
ASTM D3029 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Rockwell Hardness (R-Scale)
|
|
|
ASTM D785 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Deflection Temperature Under Load
|
ASTM D648 | ||
|
66 psi, Unannealed, 0.252 in
|
|
°F
|
|
|
264 psi, Unannealed, 0.252 in
|
|
°F
|
|
|
CLTE - Flow
|
|
in/in/°F
|
ASTM D696 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Volume Resistivity
|
|
ohm·cm
|
ASTM D257 |
|
Dielectric Constant
|
|
|
ASTM D150 |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating (0.0630 in)
|
|
|
UL 94 |
| Optical |
Nominal Value
|
Unit
|
Test Method
|
|
Transmittance (Total, 118 mil)
|
|
%
|
ASTM D1003 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: ASTALON™ S1000UR, ASTALON S1000UR, ASTALON™ , ASTALON, ASTALONS1000UR, S 1000 UR, S1000UR, S1000, 1000UR, Polycarbonate, PC, Marplex, 1000S
|
|||
| Features | |||
|
Features may also be described by the following terms: Medium Viscosity, Medium Flow, Medium Melt, Medium MFI, Medium Clarity, Good Toughness, Tough, Medium Heat Resistance, Good Processability, Easy Processing.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Housings, Housing, Automotive Applications, Automotive Sector.
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
|
°F
|
|
|
Drying Time
|
|
hr
|
|
|
Rear Temperature
|
|
°F
|
|
|
Middle Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Processing (Melt) Temp
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
|
Injection Pressure
|
|
psi
|
|
|
Injection Rate
|
|
|
|
|
Back Pressure
|
|
psi
|
|
|
Screw Speed
|
|
rpm
|
|
|
Clamp Tonnage
|
|
tons/in²
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 20.79 in/min |
| 30.11 in/min |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |