Home > Plastics > Materials > ASTALON™ > ASTALON™ H3000R - Datasheet

ASTALON™ H3000R Data Sheet

Polycarbonate

Supplied by Marplex Australia Pty. Ltd.

View Complete Data Sheet Search 95000+ Data Sheets
Create Your Free Account!
Product Description
ASTALON™ H3000R / H3001R / H3003R are the low viscosity (ultra high melt flow) grades in the ASTALON™ range and are well suited to intricate or "difficult to fill" injection moulding applications which require a mould release agent (R). Offering an excellent balance of transparency, toughness, heat resistance, flame retardancy and processability, typical applications include drinking tumblers, food processors and other kitchen appliances and domestic serving trays.

Note: [ Standard grade = H3000R ] / [ FDA approved = H3001R ] / [ Steam resistant = H3003R ].
General  
Material Status 
  • Commercial: Active
Availability 
  • Asia Pacific
  • Latin America
  • North America
Additive 
  • Mold Release
Features 
  • Flame Retardant
  • Good Processability
  • Good Toughness
  • High Flow
  • Low Viscosity
  • Medium Clarity
  • Medium Heat Resistance
Uses 
  • Appliances
  • Non-specific Food Applications
 
Processing Method 
  • Injection Molding
Physical
Nominal Value
Unit
Test Method
Specific Gravity
 
ASTM D792
Melt Mass-Flow Rate (MFR) (300°C/1.2 kg)
g/10 min
ASTM D1238
Molding Shrinkage - Flow (0.118 in)
in/in
ASTM D955
Water Absorption (24 hr)
%
ASTM D570
Mechanical
Nominal Value
Unit
Test Method
Tensile Strength 2 (0.126 in)
psi
ASTM D638
Tensile Elongation 2 (Break, 0.126 in)
%
ASTM D638
Flexural Modulus 3 (0.252 in)
psi
ASTM D790
Flexural Strength 3 (0.252 in)
psi
ASTM D790
Impact
Nominal Value
Unit
Test Method
Notched Izod Impact (0.126 in)
ft·lb/in
ASTM D256
Gardner Impact (0.126 in)
in·lb
ASTM D3029
Hardness
Nominal Value
Unit
Test Method
Rockwell Hardness (R-Scale)
 
ASTM D785
Thermal
Nominal Value
Unit
Test Method
Deflection Temperature Under Load
    ASTM D648
66 psi, Unannealed, 0.252 in
°F
 
264 psi, Unannealed, 0.252 in
°F
 
CLTE - Flow
in/in/°F
ASTM D696
Electrical
Nominal Value
Unit
Test Method
Volume Resistivity
ohm·cm
ASTM D257
Dielectric Constant
 
ASTM D150
Flammability
Nominal Value
Unit
Test Method
Flame Rating (0.0630 in)
 
UL 94
Optical
Nominal Value
Unit
Test Method
Transmittance (Total, 118 mil)
%
ASTM D1003
Features
Features may also be described by the following terms: Low Viscosity, High Flow, High Melt, High MFI, Medium Clarity, Good Toughness, Tough, Medium Heat Resistance, Good Processability, Easy Processing.
Uses
Uses may also be described by the following terms: Food Applications.
Available Documents
Technical Datasheet (English)
Injection
Nominal Value
Unit
 
Drying Temperature
°F
 
Drying Time
hr
 
Rear Temperature
°F
 
Middle Temperature
°F
 
Front Temperature
°F
 
Processing (Melt) Temp
°F
 
Mold Temperature
°F
 
Injection Pressure
psi
 
Injection Rate
 
 
Back Pressure
psi
 
Screw Speed
rpm
 
Clamp Tonnage
tons/in²
 
Notes
1Typical properties: these are not to be construed as specifications.
20.79 in/min
30.11 in/min
 
UL and the UL logo are trademarks of UL LLC © 2014. All Rights Reserved.
The information presented on this datasheet was acquired by UL Prospector from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL Prospector assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier.