| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Features
|
|
|||
|
Agency Ratings
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Molding Shrinkage - Flow
|
|
in/in
|
ASTM D955 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength (Yield)
|
|
psi
|
ASTM D638 |
|
Tensile Elongation (Yield)
|
|
%
|
ASTM D638 |
|
Flexural Strength (Yield)
|
|
psi
|
ASTM D790 |
|
Compressive Strength
|
|
psi
|
ASTM D695 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Durometer Hardness (Shore D)
|
|
|
ASTM D2240 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
CLTE - Flow
|
|
in/in/°F
|
ASTM D696 |
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Volume Resistivity
|
|
ohm·cm
|
ASTM D257 |
|
Dielectric Strength
|
|
V/mil
|
ASTM D149 |
|
Dielectric Constant (60 Hz)
|
|
|
ASTM D150 |
|
Dissipation Factor (60 Hz)
|
|
|
ASTM D150 |
| Thermoset |
Nominal Value
|
Unit
|
Test Method
|
|
Thermoset Components
|
|||
|
Hardener
|
|
|
|
|
Resin
|
|
|
|
|
Pot Life (72°F)
|
|
min
|
|
|
Shelf Life
|
|
wk
|
|
|
Thermoset Mix Viscosity
|
|
cP
|
ASTM D2393 |
|
Demold Time
|
|||
|
72°F
|
|
min
|
|
|
150°F
|
|
min
|
|
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Insulcast Epoxy 129/Insulcure 9, Insulcast Epoxy 129Insulcure 9, Insulcast Epoxy , InsulcastEpoxy129Insulcure9, InsulcastEpoxy, Epoxy 129 Insulcure 9, Epoxy 129, 129, Epoxy129/Insulcure 9, Epoxy129Insulcure 9, Epoxy129:Insulcure 9, Epoxy129+Insulcure 9, Epoxy129-Insulcure 9, Epoxy129_Insulcure 9, Epoxy129 Insulcure 9, Epoxy129, Epoxy129Insulcure9, 129/Insulcure 9, 129Insulcure 9, 129:Insulcure 9, 129+Insulcure 9, 129-Insulcure 9, 129_Insulcure 9, 129 Insulcure 9, 129Insulcure, Insulcure9, Epoxy129_Insulcure9, 129Insulcure9, 129_Insulcure9, Epoxy; Epoxide, Epoxy Epoxide, Epoxy, Permagile, EpoxyEpoxide, Insulcure129, 129Epoxy
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Adhesion.
|
|||
| Agency Ratings | |||
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): MIL (1).
|
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |