| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Filler / Reinforcement
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Automotive Specifications
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR) (265°C/2.16 kg)
|
|
g/10 min
|
ASTM D1238 |
|
Molding Shrinkage - Flow
|
|
in/in
|
ASTM D955 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength (Yield, 73°F)
|
|
psi
|
ASTM D638 |
|
Tensile Elongation (Break, 73°F)
|
|
%
|
ASTM D638 |
|
Flexural Modulus (73°F)
|
|
psi
|
ASTM D790 |
|
Flexural Strength (73°F)
|
|
psi
|
ASTM D790 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact (73°F)
|
|
ft·lb/in
|
ASTM D256 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Rockwell Hardness (R-Scale, 73°F)
|
|
|
ASTM D785 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Deflection Temperature Under Load
|
ASTM D648 | ||
|
66 psi, Unannealed
|
|
°F
|
|
|
264 psi, Unannealed
|
|
°F
|
|
|
Melting Temperature
|
|
°F
|
DSC |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating (0.0315 in)
|
|
|
UL 94 |
| Additional Information |
Nominal Value
|
Unit
|
Test Method
|
|
Filler Content 2
|
|
%
|
ASTM D5630 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Kepex® 3730GF, Kepex 3730GF, Kepex® , Kepex, Kepex3730GF, 3730 GF, 3730GF, Polybutylene Terephthalate + PET, Polybutylene Terephthalate PET, Polybutylene Terephthalate : PET, Polybutylene Terephthalate / PET, Polybutylene Terephthalate - PET, Polybutylene Terephthalate _ PET, Polybutylene Terephthalate PET, PBT+PET, PBTPET, PBT:PET, PBT/PET, PBT-PET, PBT_PET, PBT PET, Polyester, Korea Eng, PolybutyleneTerephthalatePET, PolybutyleneTerephthalate_PET, GF3730
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Surface Finish, Good Weather Resistance, Weather Resistant.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Automotive Applications, Automotive Sector, Electrical Applications, Electronic Applications, Electrical/Electronic Applications, Electrical Sector.
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 1 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): GM (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Rear Temperature
|
|
°F
|
|
|
Middle Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
| 2Furnace |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |