| Product Description | ||||
|
QUATTOR® ES-60004 is a homopolymer high-density polyethylene, produced through Unipol® process and recommended for use in small bottles and containers up to 5 liters.
Bottles obtained using QUATTOR® ES-60004 exhibit excellent smell properties and a high top load resistance. Applications: bottles for lubricating and edible oils, bottles for cosmetics, milk, juice and yogurt, toys. |
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Agency Ratings
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ASTM D1505 |
|
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
|
|
g/10 min
|
ASTM D1238 |
|
Environmental Stress-Cracking Resistance (122°F, 10% Igepal, F50)
|
|
hr
|
ASTM D1693B |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength (Yield)
|
|
psi
|
ASTM D638 |
|
Tensile Elongation (Yield)
|
|
%
|
ASTM D638 |
|
Flexural Modulus
|
|
psi
|
ASTM D790 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Unnotched Izod Impact
|
|
ft·lb/in
|
ASTM D256 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Durometer Hardness (Shore D)
|
|
|
ASTM D2240 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Deflection Temperature Under Load (66 psi, Unannealed)
|
|
°F
|
ASTM D648 |
|
Vicat Softening Temperature
|
|
°F
|
ASTM D1525 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Quattor® ES-60004, Quattor ES60004, Quattor® , Quattor, QuattorES60004, ES, ES-60004, ES60004, ES:60004, ES/60004, ES+60004, ES_60004, ES 60004, Polyethylene, High Density, Polyethylene High Density, HDPE, Polyethylene, PE, Quattor Petroquimica, PolyethyleneHighDensity, 60004ES
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Organoleptic Properties.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Food Packaging.
|
|||
| Agency Ratings | |||
|
This plastic material has 3 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): EU (1), FDA (1), ANVISA (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Rear Temperature
|
|
°F
|
|
|
Middle Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
| Injection Notes | |||
|
Die Temperature: 195°C
Parison Temperature: 200°C |
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |