| Product Description | ||||
|
Quattor® BF-22020 S3 is a linear low density polyethylene, butene copolymer, produced through Unipol® process and recommended for blown film extrusion.
Films produced using Quattor® BF-22020 S3 have good processability, better mechanical performance in comparison to conventional low density polyethylene (LDPE) and are easily welded even at high speed packaging machines. Applications: automatic packaging (FFS), general purpose, blends with HDPE and LDPE and lamination. |
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Additive
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Processing Method
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ASTM D1505 |
|
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
|
|
g/10 min
|
ASTM D1238 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Coefficient of Friction (vs. Itself - Dynamic, Blown Film)
|
|
|
ASTM D1894 |
| Films |
Nominal Value
|
Unit
|
Test Method
|
|
Film Thickness - Tested
|
|
mil
|
|
|
Tensile Strength
|
ASTM D882 | ||
|
MD: Yield, 0.98 mil, Blown Film
|
|
psi
|
|
|
TD: Yield, 0.98 mil, Blown Film
|
|
psi
|
|
|
MD: Break, 0.98 mil, Blown Film
|
|
psi
|
|
|
TD: Break, 0.98 mil, Blown Film
|
|
psi
|
|
|
Tensile Elongation
|
ASTM D882 | ||
|
MD: Yield, 0.98 mil, Blown Film
|
|
%
|
|
|
TD: Yield, 0.98 mil, Blown Film
|
|
%
|
|
|
MD: Break, 0.98 mil, Blown Film
|
|
%
|
|
|
TD: Break, 0.98 mil, Blown Film
|
|
%
|
|
|
Dart Drop Impact (0.98 mil, Blown Film)
|
|
g
|
ASTM D1709A |
|
Elmendorf Tear Strength
|
ASTM D1922 | ||
|
MD: 0.98 mil, Blown Film
|
|
g
|
|
|
TD: 0.98 mil, Blown Film
|
|
g
|
|
| Optical |
Nominal Value
|
Unit
|
Test Method
|
|
Gloss (45°)
|
|
|
ASTM D2457 |
|
Haze
|
|
%
|
ASTM D1003 |
| Additional Information | |||
|
Film data obtained on 25 µm thickness film produced on a 75 mm extruder, blow up ratio 2.2:1, die gap 2.1 mm, and 120 kg/h output
|
|||
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Quattor® BF-22020 S3, Quattor BF22020 S3, Quattor® , Quattor, QuattorBF22020S3, BF, BF 22020 S 3, BF-22020 S3, BF22020 S3, BF:22020 S3, BF/22020 S3, BF+22020 S3, BF_22020 S3, BF 22020 S3, BF22020, 22020S, S3, BF22020S3, BF_22020S3, Polyethylene, Linear Low Density, Polyethylene Linear Low Density, LLDPE, Polyethylene, PE, Quattor Petroquimica, PolyethyleneLinearLowDensity, 22020BF
|
|||
| Features | |||
|
Features may also be described by the following terms: Good Processability, Easy Processing, Butene Comonomer, Antiblocking, Unspecified Antiblock, Slip, Unspecified Slip.
|
|||
| Extrusion |
Nominal Value
|
Unit
|
|
|
Cylinder Zone 1 Temp.
|
|
°F
|
|
|
Cylinder Zone 2 Temp.
|
|
°F
|
|
|
Cylinder Zone 3 Temp.
|
|
°F
|
|
|
Cylinder Zone 4 Temp.
|
|
°F
|
|
|
Cylinder Zone 5 Temp.
|
|
°F
|
|
|
Melt Temperature
|
|
°F
|
|
| Extrusion Notes | |||
|
Blow-up Ratio: 2.0 to 3.0:1
Minimum Thickness: 15 microns per wall |
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |