| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Features
|
|
|||
|
Uses
|
|
|||
|
Agency Ratings
|
|
|||
|
UL File Number
|
|
|||
|
Appearance
|
|
|||
|
Forms
|
|
|||
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR) (200°C/5.0 kg)
|
|
g/10 min
|
ASTM D1238 |
|
Molding Shrinkage - Flow
|
|
in/in
|
ASTM D955 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus (Injection Molded)
|
|
psi
|
ASTM D638 |
|
Tensile Strength
|
ASTM D638 | ||
|
Break, Injection Molded
|
|
psi
|
|
|
Injection Molded
|
|
psi
|
|
|
Tensile Elongation (Break, Injection Molded)
|
|
%
|
ASTM D638 |
|
Flexural Modulus (Injection Molded)
|
|
psi
|
ASTM D790 |
|
Flexural Strength (Injection Molded)
|
|
psi
|
ASTM D790 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact (73°F, Injection Molded)
|
|
ft·lb/in
|
ASTM D256 |
| Hardness |
Nominal Value
|
Unit
|
Test Method
|
|
Rockwell Hardness (L-Scale)
|
|
|
ASTM D785 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Deflection Temperature Under Load
|
ASTM D648 | ||
|
66 psi, Unannealed
|
|
°F
|
|
|
264 psi, Unannealed
|
|
°F
|
|
|
Vicat Softening Temperature
|
|
°F
|
ASTM D1525 |
|
CLTE - Flow
|
|
in/in/°F
|
ASTM D696 |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating
|
|
|
UL 94 |
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: Americas Styrenics MB3150-AMST, Americas Styrenics MB3150AMST, Americas Styrenics , AmericasStyrenicsMB3150AMST, AmericasStyrenics, MB 3150, StyrenicsMB 3150 AMST, StyrenicsMB 3150, StyrenicsMB3150-AMST, StyrenicsMB3150AMST, StyrenicsMB3150:AMST, StyrenicsMB3150/AMST, StyrenicsMB3150+AMST, StyrenicsMB3150_AMST, StyrenicsMB3150 AMST, StyrenicsMB3150, MB 3150 AMST, MB3150-AMST, MB3150AMST, MB3150:AMST, MB3150/AMST, MB3150+AMST, MB3150_AMST, MB3150 AMST, MB3150, 3150AMST, PS, Polystyrene, General Purpose, Polystyrene General Purpose, PS (GPPS), PS GPPS, Polystyrene, PolystyreneGeneralPurpose, PSGPPS, 3150MB, 3150StyrenicsMB
|
|||
| Features | |||
|
Features may also be described by the following terms: High Heat Resistance, Fast Cycle, Rapid Cycle, Productivity, Fast Molding Cycle, Good Toughness, Tough, High Clarity.
|
|||
| Uses | |||
|
Uses may also be described by the following terms: Media Packaging.
|
|||
| Agency Ratings | |||
|
This plastic material has 1 certifications from the following agencies (the number in parentheses shows the number of certifications for that agency): FDA (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Rear Temperature
|
|
°F
|
|
|
Middle Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Nozzle Temperature
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
|
Injection Rate
|
|
|
|
|
Back Pressure
|
|
psi
|
|
|
Cushion
|
|
in
|
|
| Extrusion |
Nominal Value
|
Unit
|
|
|
Cylinder Zone 1 Temp.
|
|
°F
|
|
|
Cylinder Zone 2 Temp.
|
|
°F
|
|
|
Cylinder Zone 3 Temp.
|
|
°F
|
|
|
Cylinder Zone 4 Temp.
|
|
°F
|
|
|
Cylinder Zone 5 Temp.
|
|
°F
|
|
|
Adapter Temperature
|
|
°F
|
|
|
Melt Temperature
|
|
°F
|
|
|
Die Temperature
|
|
°F
|
|
| Extrusion Notes | |||
|
Zone 6 Temperature: 204 to 221°C
Melt Pump, Pipes, Screen Changer Temperature: 193 to 232°C Polish Rolls Temperature: 66 to 104°C Head Pressure: 10 to 21 MPa |
|||
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |