| Product Description | ||||
|
Delrin® 100PE NC010 (formerly DE20573) is a high viscosity acetal homopolymer, an enhanced version of Delrin® 100P with very low VOC emissions. It has the best combination of strength and toughness and improved processing productivity for injection molding.
|
||||
| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Part Marking Code (ISO 11469)
|
|
|||
|
Resin ID (ISO 1043)
|
|
|||
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Mass-Flow Rate (MFR) (190°C/2.16 kg)
|
|
g/10 min
|
ISO 1133 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus (73°F)
|
|
psi
|
ISO 527-2 |
|
Tensile Stress (Yield, 73°F)
|
|
psi
|
ISO 527-2 |
|
Tensile Strain
|
|||
|
Yield, 73°F
|
|
%
|
ISO 527-2 |
|
Break, 73°F
|
|
%
|
ISO 527-2/50 |
|
Nominal Tensile Strain at Break (73°F)
|
|
%
|
ISO 527-2 |
|
Flexural Modulus (73°F)
|
|
psi
|
ISO 178 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Charpy Notched Impact Strength
|
ISO 179/1eA | ||
|
-22°F
|
|
ft·lb/in²
|
|
|
73°F
|
|
ft·lb/in²
|
|
|
Charpy Unnotched Impact Strength (73°F)
|
|
|
ISO 179/1eU |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature (264 psi, Unannealed)
|
|
°F
|
ISO 75-2/A |
|
Melting Temperature 3
|
|
°F
|
ISO 11357-3 |
| Related Terminology | |||
|
This supplier and product may also be known by these terms: DerlinProduct names can be difficult to match. You may have searched any one of these terms to find this product: Delrin® 100PE NC010, Delrin 100PE NC010, Delrin® , Delrin, Delrin100PENC010, 100 PE NC 010, 100PE NC010, 100PE, PENC, NC010, 100PENC010, Acetal Homopolymer, Acetal Homopolymer, Acetal (POM) Homopolymer, Acetal POM Homopolymer, Acetal, pom, DuPont, AcetalPOMHomopolymer, PE100
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
|
°F
|
|
|
Drying Time - Desiccant Dryer
|
|
hr
|
|
|
Suggested Max Moisture
|
|
%
|
|
|
Processing (Melt) Temp
|
|
°F
|
|
|
Melt Temperature, Optimum - Injection Molding
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
|
Mold Temperature, Optimum - Injection Molding
|
|
°F
|
| Notes |
| 1The above data are preliminary and are subject to change as additional data are developed on subsequent lots. |
| 2Typical properties: these are not to be construed as specifications. |
| 310°C/min |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |