| General | ||||
|
Material Status
|
|
|||
|
Availability
|
|
|||
|
Features
|
|
|||
|
Automotive Specifications
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Density
|
|
g/cm³
|
ISO 1183 |
|
Melt Mass-Flow Rate (MFR) (300°C/1.2 kg)
|
|
g/10 min
|
ISO 1133 |
|
Melt Volume-Flow Rate (MVR) (300°C/1.2 kg)
|
|
in³/10min
|
ISO 1133 |
|
Molding Shrinkage
|
No Standard | ||
|
Across Flow: 0.126 in
|
|
%
|
|
|
Flow: 0.126 in
|
|
%
|
|
|
Water Absorption (Saturation, 73°F)
|
|
%
|
ISO 62 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Modulus
|
|
psi
|
ISO 527-2 |
|
Tensile Stress (Yield)
|
|
psi
|
ISO 527-2 |
|
Tensile Strain (Yield)
|
|
%
|
ISO 527-2 |
|
Nominal Tensile Strain at Break
|
|
%
|
ISO 527-2 |
|
Flexural Modulus
|
|
psi
|
ISO 178 |
|
Flexural Strength
|
|
psi
|
ISO 178 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Charpy Notched Impact Strength (73°F)
|
|
ft·lb/in²
|
ISO 179 |
|
Charpy Unnotched Impact Strength (73°F)
|
|
|
ISO 179 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Heat Deflection Temperature
|
|||
|
66 psi, Unannealed
|
|
°F
|
ISO 75-2/B |
|
264 psi, Unannealed
|
|
°F
|
ISO 75-2/A |
|
CLTE
|
ISO 11359-2 | ||
|
Flow
|
|
in/in/°F
|
|
|
Transverse
|
|
in/in/°F
|
|
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Surface Resistivity
|
|
ohm
|
IEC 60093 |
|
Volume Resistivity
|
|
ohm·cm
|
IEC 60093 |
|
Electric Strength
|
IEC 60243-1 | ||
|
0.0394 in
|
|
V/mil
|
|
|
0.118 in
|
|
V/mil
|
|
|
Relative Permittivity
|
IEC 60250 | ||
|
100 Hz
|
|
|
|
|
1 MHz
|
|
|
|
|
Dissipation Factor
|
IEC 60250 | ||
|
100 Hz
|
|
|
|
|
1 MHz
|
|
|
|
|
Comparative Tracking Index (CTI)
|
|
|
UL 746 |
| Additional Information | |||
|
S-2000V(R): V-2
S-2000R: Mold Release S-2000U(R): UV Stabilized S-2001(R): FDA compliant |
|||
| Related Terminology | |||
|
This supplier and product may also be known by these terms: Lupilon, JupilonProduct names can be difficult to match. You may have searched any one of these terms to find this product: Iupilon® S-2000, Iupilon S2000, Iupilon® , Iupilon, IupilonS2000, S-2000, S2000, S:2000, S/2000, S+2000, S_2000, S 2000, Polycarbonate, PC, Mitsubishi EP, 2000S
|
|||
| Features | |||
|
Features may also be described by the following terms: Medium Viscosity.
|
|||
| Automotive Specifications | |||
|
This plastic material has approval for 2 automotive specifications from the following agencies (the number in parentheses shows the number of specifications for that agency): CHRYSLER (1), GM (1).
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
|
°F
|
|
|
Drying Time
|
|
hr
|
|
|
Rear Temperature
|
|
°F
|
|
|
Middle Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Nozzle Temperature
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
|
|
Injection Pressure
|
|
psi
|
|
|
Screw Speed
|
|
rpm
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |