| Product Description | |
|
EMI / ESD SHIELDING
|
|
| General | |
|
Material Status
|
|
|
Availability
|
|
|
Filler / Reinforcement
|
|
|
Features
|
|
|
Forms
|
|
|
Processing Method
|
|
| Physical |
Nominal Value
|
Unit
|
Test Method
|
|
Specific Gravity
|
|
|
ASTM D792 |
|
Melt Mass-Flow Rate (MFR) (230°C/3.8 kg)
|
|
g/10 min
|
ASTM D1238 |
|
Molding Shrinkage - Flow
|
|
in/in
|
ASTM D955 |
| Mechanical |
Nominal Value
|
Unit
|
Test Method
|
|
Tensile Strength
|
ASTM D638 | ||
|
Yield
|
|
psi
|
|
|
Break
|
|
psi
|
|
|
Flexural Modulus
|
|
psi
|
ASTM D790 |
|
Flexural Strength
|
|
psi
|
ASTM D790 |
| Impact |
Nominal Value
|
Unit
|
Test Method
|
|
Notched Izod Impact (40°F)
|
|
ft·lb/in
|
ASTM D256 |
| Thermal |
Nominal Value
|
Unit
|
Test Method
|
|
Deflection Temperature Under Load
|
ASTM D648 | ||
|
66 psi, Unannealed, 0.125 in
|
|
°F
|
|
|
264 psi, Unannealed, 0.125 in
|
|
°F
|
|
| Electrical |
Nominal Value
|
Unit
|
Test Method
|
|
Surface Resistivity
|
|
ohm
|
ASTM D257 |
| Flammability |
Nominal Value
|
Unit
|
Test Method
|
|
Flame Rating
|
UL 94 | ||
|
0.0625 in
|
|
|
|
|
0.125 in
|
|
|
|
| Additional Information | |||
|
Melt Mass- Flow Rate (MFR), ASTM D1238, 230°C/ 3.8kg: 10 to 20 g/10 min
Surface Resitivity, ASTM D257: 1E1 to 1E2 ohms |
|||
| Related Terminology | |||
|
Product names can be difficult to match. You may have searched any one of these terms to find this product: OP - ABS ABS FR 15SS, OP ABS ABS FR 15SS, OP - ABS , OP ABS, OP : ABS, OP / ABS, OP + ABS, OP _ ABS, OP ABS, OPABSABSFR15SS, OPABS, ABSABS FR 15 SS, OP_ABS, ABSABS FR 15SS, ABSABSFR, ABS, ABS FR 15 SS, ABSABSFR15SS, ABS FR 15SS, ABSFR, FR15, 15SS, ABSFR15SS, Acrylonitrile Butadiene Styrene, Oxford Polymers, AcrylonitrileButadieneStyrene, FRABS, FRABSABS
|
|||
| Injection |
Nominal Value
|
Unit
|
|
|
Drying Temperature
|
|
°F
|
|
|
Drying Time
|
|
hr
|
|
|
Rear Temperature
|
|
°F
|
|
|
Middle Temperature
|
|
°F
|
|
|
Front Temperature
|
|
°F
|
|
|
Processing (Melt) Temp
|
|
°F
|
|
|
Mold Temperature
|
|
°F
|
| Notes |
| 1Typical properties: these are not to be construed as specifications. |
|
UL and the UL logo are trademarks of UL LLC © 2013. All Rights Reserved.
The information presented on this datasheet was acquired by UL IDES from the producer of the material. UL IDES makes substantial efforts to assure the accuracy of this data. However, UL IDES assumes no responsibility for the data values and strongly encourages that upon final material selection, data points are validated with the material supplier. |